Messages

1

Zaurus - pdaXrom / File Size Limit For Usb-net?

« on: January 23, 2006, 09:52:39 am »

Hi all,

when I try to copy file from zaurus to notebook I can not do it for files larger that about 1.5KB. I can set up usb network and it does work fine, but sending file via scp or ftp works only for very small files.

Also, when I work on zaurus via ssh sometimes it happens that the connection hangs up - I am not sure, but maybe it happens also when SSH has larger amount of data to be send.

I use SLC-760 with pdaXrom 1.1.0beta1. On notebook there is Debian.

If anyone could help - it would be great. I can not handle this problem since few days.

Thanks in advance,
Jakub

iptables settings:

Chain INPUT (policy ACCEPT)
target     prot opt source               destination
ACCEPT     all  --  anywhere             anywhere
ACCEPT     icmp --  anywhere             anywhere
LOG        all  --  anywhere             anywhere            LOG level warning prefix `ipusb0in'

Chain FORWARD (policy ACCEPT)
target     prot opt source               destination
ACCEPT     all  --  192.168.0.0/24       anywhere
ACCEPT     all  --  anywhere             192.168.0.0/24

Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination
LOG        all  --  anywhere             anywhere            LOG level warning prefix `ipusb0out'
ACCEPT     all  --  anywhere             anywhere
ACCEPT     all  --  anywhere             anywhere

2

Zaurus - pdaXrom / File Size Limit For Usb-net?

« on: January 23, 2006, 09:37:11 am »

Hi all,

when I try to copy file from zaurus to notebook I can not do it for files larger that about 1.5KB. I can set up usb network and it does work fine, but sending file via scp or ftp works only for very small files.

Also, when I work on zaurus via ssh sometimes it happens that the connection hangs up - I am not sure, but maybe it happens also when SSH has larger amount of data to be send.

I use SLC-760 with pdaXrom 1.1.0beta1. On notebook there is Debian.

If anyone could help - it would be great. I can not handle this problem since few days.

Thanks in advance,
Jakub

iptables settings:

Chain INPUT (policy ACCEPT)
target     prot opt source               destination
ACCEPT     all  --  anywhere             anywhere
ACCEPT     icmp --  anywhere             anywhere
LOG        all  --  anywhere             anywhere            LOG level warning prefix `ipusb0in'

Chain FORWARD (policy ACCEPT)
target     prot opt source               destination
ACCEPT     all  --  192.168.0.0/24       anywhere
ACCEPT     all  --  anywhere             192.168.0.0/24

Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination
LOG        all  --  anywhere             anywhere            LOG level warning prefix `ipusb0out'
ACCEPT     all  --  anywhere             anywhere
ACCEPT     all  --  anywhere             anywhere

3

Sharp ROMs / Problems With Konsole And Mc In Cacko 1.23

« on: January 05, 2006, 10:31:39 am »

Maybe somebody else will have similar problem so I will write what was the reason - the reason for that was package japanese-support, after uninstalling it both console and midnight commander work fine.

4

Sharp ROMs / Problems With Konsole And Mc In Cacko 1.23

« on: December 22, 2005, 08:00:51 am »

Hi,

I have installed newest Cacko - 1.23. I love it - bluetooth, usb-net and some other sutff works just plug'n'play  

But afterwards I have installed also some more packages from Cackofeed and now I can not run Konsole and Midnight Commander. All other apps are going well, but these two - not any more.

What's wrong, what should I do?

I use SLC-760.

Thank's in advance,
Jakub

5

Angstrom & OpenZaurus / Trying To Start Up Bluetooth On Oz

« on: September 09, 2005, 09:29:37 am »

Thank you both for your support. I have tried also with BT modules I have found, but still could not get it working. After installing all of these packages my OpenZaurus started to have other problems - I can not suspend it or even switch it off (have to remove battery). Another thing is that setserial hangs up (and even can not be killed -9). TOP shows load average about 2 (before it was about 0).

I am going to check pdaXrom and if I can set it up (with bluetooth etc.) in few days it will be great, if not I will switch back to Cacko (bluetooth was working there "out of the box").

Thanks again, hope one day I can try OZ again

6

Angstrom & OpenZaurus / Trying To Start Up Bluetooth On Oz

« on: September 08, 2005, 04:51:56 am »

I have following results:

Code: [Select]

# cardctl ident
Socket 0:
  product info: "Compact Flash", "Bluetooth Card", "", ""
  manfid: 0x0279, 0x950b
  function: 2 (serial)
And file /etc/pcmcia/bluetooth.conf contains:

Code: [Select]

card "Billionton Bluetooth Card"
  version "Compact Flash", "Bluetooth Card"
  bind "serial_cs" class "bluetooth"
What else can I do?

7

Angstrom & OpenZaurus / Trying To Start Up Bluetooth On Oz

« on: September 07, 2005, 07:06:34 am »

I have done all the steps you have written up to "setserial", including installation of "kernel-module-bluecard-cs" and editing bluetooth.conf.

In the meantime I have found also other modules which are required for setserial to work. But hciattach returns following result:

Code: [Select]

# hciattach /dev/ttyS3 billionton
Unknown device type or id
I have tried also with other parameter:

Code: [Select]

# hciattach /dev/ttyS3 bcsp
Can't get port settings: Input/output error
Can't initialize device: Illegal seek
How can I get hciattach working?

8

Angstrom & OpenZaurus / Trying To Start Up Bluetooth On Oz

« on: September 07, 2005, 06:44:20 am »

First of all - thank you for your help!

I have done all the steps untill:

Try issuing the following commands in this order:

Code: [Select]

setserial /dev/ttyS3 baud_base 921600
modprobe hci_uart
hciattach /dev/ttyS3 billionton
hciconfig hci0 up

setserial result is following:

Code: [Select]

# setserial /dev/ttyS3 baud_base 921600
/dev/ttyS3: No such device or address
I guess it is again problem with lack of some modules. It took me long time untill I have realised that OpenZaurus default kernel does not include many modules such us bluetooth etc. They are also not in standard feed, they just have to be downloaded from http://www.rpsys.net/openzaurus/packages/

Do you know which modules should I download to have setserial working? I was trying with some, but without any results.

9

Poland / Problem Z Bluetoothem Na Openzaurusie

« on: September 06, 2005, 10:34:54 am »

Cześć,

jestem świeżo upieczonym posiadaczem używanego SL-C760, który miał zainstalowane Cacko. Kupiłem do niego kartę Bluetooth Billionton i na Cacku zadziałała praktycznie "plug-and-play".

Zainstalowałem jednak OpenZaurusa i fajny jest, bo szybciej chodzi, ale niestety za nic nie mogę odpalić już bluetootha.

Karta wygląda na poprawnie wykrywaną:
# cardctl ident
Socket 0:
  product info: "Compact Flash", "Bluetooth Card", "", ""
  manfid: 0x0279, 0x950b
  function: 2 (serial)

ale to koniec dobrych wiadomości, bo:
# sdptool browse
Inquiring ...
Inquiry failed
# hcitool scan
Device is not available: Address family not supported by protocol

i utknąłem. Przerobiłem różne HOW-TO i wątki na forum, instalowałem różne wersje bluez ale bez skutku. Czy ktoś z Was ma może doświadczenie w tym temacie i mógłby mi pomóc?

Dzięki z góry,
Kuba z Wrocławia

10

Angstrom & OpenZaurus / Trying To Start Up Bluetooth On Oz

« on: September 06, 2005, 10:26:26 am »

Does anyone can give me any suggestion what should I do?

I'm just about switching back to Cacko, but OZ seems to run faster so I still would like to have some try...

11

Security and Networking / Bluetooth Via Billionton Cf Card On Openzaurus

« on: September 06, 2005, 10:06:06 am »

Hi,

I am trying to start up bluetooth on Billionton CF card CFBT02-B2 on SL-C760. Previously it was running on Cacko and it was working fine almost "out of the box". But since I have installed OpenZaurus 3.5.3 I can not manage it. I have tried steps from many different HOW-TOs and also some forums threads but I have no good results. It seems that most of instructions are for 2.4 kernel, but OZ has 2.6.

It seems that card is discovered:

# cardctl ident
Socket 0:
  product info: "Compact Flash", "Bluetooth Card", "", ""
  manfid: 0x0279, 0x950b
  function: 2 (serial)

but one can not use it:

# sdptool browse
Inquiring ...
Inquiry failed
# hcitool scan
Device is not available: Address family not supported by protocol

Please, could you help me?

Regards,
Jakub

12

Angstrom & OpenZaurus / Trying To Start Up Bluetooth On Oz

« on: September 05, 2005, 09:55:52 am »

Hi,

I have Billionton CF BlueTooth card and I am trying to get it to work since few days without success
At first I had Cacko and it worked fine, but I have switched to OZ 3.5.3 and I can not start it up. I have tried to follow few HOW-TOs, but no good results.

When I insert card into slot it is automatically discovered in status bar as "Billionton Bluetooth Card" and it blinks. And this is the only positive response.

# sdptool browse
Inquiring ...
Inquiry failed

# hcitool scan
Device is not available.: Address family not supported by protocol

# cardctl status
Socket 0:
  3.3V 16-bit PC Card
  function 0: [ready]

#  setserial /dev/ttyS3 baud_base 921600
/dev/ttyS3: No such device or address

(yes, /dev/ttyS3 exists)

Where is my fault, what should I do? please help,
Jakub