Messages

1

Security and Networking / C3000 Planex Cf11: Who Is Able To Run It?

« on: October 15, 2005, 02:46:56 am »

I was amazing when I saw the opie desktop after the installation of openzaurus.
But after two days of hacks in google, I am thinking to give up, because my Planex CF11 wlan card
seems to be alergic to Zaurus.
in fact, even if I can see the ap signal on the network->setting, I can access the HTTP.
Anyone succedeed in this wokr?
G
[div align=\"right\"][a href=\"index.php?act=findpost&pid=98797\"][{POST_SNAPBACK}][/a][/div]

Hello
I have been successful in running this card in OZ on a c3000.  Did you try the kernel in the OZ updates feed?  The older kernel dated in April did not work for me, but the kernel dated in May did.  The Planex card is a prism3 device.  After using the updated kernel the card was recognised as a Sandisk Connect Plus, but connected to my AP with WEP regardless.  Wireless for this card is much nicer and hassle free in OZ than Sharp Rom.  Use the driver Mr. Figlabs proposed for Sharp Rom w/ standard Kernel or use the updated wlan-ng package (pre26) if you have tetsu's special kernel 18b.

Hope this helps.  Dont get discouraged.  The card really works.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=98825\"][{POST_SNAPBACK}][/a][/div]

Thank you. can you point me out where I shall download the May-kernel? I dowloaded it from the folder "updates", I copied the zImage into the SD card and did all necessary installation procedures.
At the firts boot, linux stop and says me: Can mount /mnt/hda
Why?
Thank you a lot again
Giuseppe
[div align=\"right\"][a href=\"index.php?act=findpost&pid=99449\"][{POST_SNAPBACK}][/a][/div]

Moreover, just now I got the new kernel. But the planex card is always blanking.
Why

2

Security and Networking / C3000 Planex Cf11: Who Is Able To Run It?

« on: October 15, 2005, 12:22:20 am »

I was amazing when I saw the opie desktop after the installation of openzaurus.
But after two days of hacks in google, I am thinking to give up, because my Planex CF11 wlan card
seems to be alergic to Zaurus.
in fact, even if I can see the ap signal on the network->setting, I can access the HTTP.
Anyone succedeed in this wokr?
G
[div align=\"right\"][a href=\"index.php?act=findpost&pid=98797\"][{POST_SNAPBACK}][/a][/div]

Hello
I have been successful in running this card in OZ on a c3000.  Did you try the kernel in the OZ updates feed?  The older kernel dated in April did not work for me, but the kernel dated in May did.  The Planex card is a prism3 device.  After using the updated kernel the card was recognised as a Sandisk Connect Plus, but connected to my AP with WEP regardless.  Wireless for this card is much nicer and hassle free in OZ than Sharp Rom.  Use the driver Mr. Figlabs proposed for Sharp Rom w/ standard Kernel or use the updated wlan-ng package (pre26) if you have tetsu's special kernel 18b.

Hope this helps.  Dont get discouraged.  The card really works.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=98825\"][{POST_SNAPBACK}][/a][/div]

Thank you. can you point me out where I shall download the May-kernel? I dowloaded it from the folder "updates", I copied the zImage into the SD card and did all necessary installation procedures.
At the firts boot, linux stop and says me: Can mount /mnt/hda
Why?
Thank you a lot again
Giuseppe

3

Security and Networking / Planex Wireless Card On C3000

« on: October 14, 2005, 11:16:58 pm »

There's a new driver for the Planex card released by Sharp:
http://216.239.39.104/translate_c?hl=en&ie.../language_tools
[div align=\"right\"][a href=\"index.php?act=findpost&pid=77354\"][{POST_SNAPBACK}][/a][/div]

This driver are for the sharp rom. I tried to install under openzaurus, but I couldn't. A lot of error got out. It seems that those drivers are for original sharp rom.
Regards

4

Security and Networking / C3000 Planex Cf11: Who Is Able To Run It?

« on: October 10, 2005, 01:50:12 am »

I was amazing when I saw the opie desktop after the installation of openzaurus.
But after two days of hacks in google, I am thinking to give up, because my Planex CF11 wlan card
seems to be alergic to Zaurus.
in fact, even if I can see the ap signal on the network->setting, I can access the HTTP.
Anyone succedeed in this wokr?
G