Author Topic: "ghosting" Caused By R121? (Read 3747 times)

Capn_Fish · « **on:** October 31, 2006, 06:02:43 pm »

I installed r121 on my C750 for a while, then restored back to beta 1. Both operations went fine.

Now I have some images "ghosted" on the screen. For instance, the Matchbox panel is solidly there, but then there is a faint "ghost" of it that appears to overlap it and is raised by about .5cm. The same thing is happening with some icons.

My question is, does r121 change any settings that would cause this? Would changing the COM and phase help?

Thanks!

InSearchOf · « **Reply #1 on:** October 31, 2006, 09:49:25 pm »

I get the same... didnt bother me toooooooooooo much yet... so I haven't complained yet... :-)

Late

bam · « **Reply #2 on:** November 01, 2006, 02:14:08 am »

adjusting com/phase would probably eliminate it.

Bundabrg · « **Reply #3 on:** November 01, 2006, 02:43:20 am »

I've got a thread somewhere about this. Definately try adjust those values. One of the steps of installing was to do a NAND erase, which resets these values.

Capn_Fish · « **Reply #4 on:** November 01, 2006, 07:47:47 am »

Is there any rule of thumb for which to adjust and which way to adjust it or can somebody with a C750 share their values (if it works like that)?

Thanks.

bam · « **Reply #5 on:** November 02, 2006, 12:00:54 am »

there is a thread in the forums somewhere dealing with the values.

found it

https://www.oesf.org/forums/index.php?showtopic=8541&st=0

Capn_Fish · « **Reply #6 on:** November 02, 2006, 07:46:45 am »

I managed to figure it out. It didn't occur to me to look at the pinned threads. Oh, well. It only took two tries.

Capn_Fish · « **Reply #7 on:** June 23, 2007, 02:35:47 pm »

Sorry for repeatedly posting this, but is there anything other than com/phase which would help this issue? No matter how I adjust them on my C3100, there is always ghosting.

Thanks.

louigi600 · « **Reply #8 on:** June 23, 2007, 03:16:59 pm »

Not sure about beta1 but beta4 and above ignored values set up with the D+M menu ... instead zaurushw read some values from /etc/sysconfig/zaurushw.

I think that the old 2.4 kernel stuff might still read stuff from flash parameter area (in mtd1 0x40000 0x7bfff:
if this is the case and you are using D+M to adjust then maybe the restore was only a partial success (might haveto dig up some stuff from a full nand backup avalible at trisoft.

If beta1 also used the zaurushw thing and you are editing the right file ... hum intresting I'd like to investigate further.

If nether of these situations suits then you're probably doing something wrong ;-)

Capn_Fish · « **Reply #9 on:** June 23, 2007, 03:22:02 pm »

Quote

Not sure about beta1 but beta4 and above ignored values set up with the D+M menu ... instead zaurushw read some values from /etc/sysconfig/zaurushw.

I think that the old 2.4 kernel stuff might still read stuff from flash parameter area (in mtd1 0x40000 0x7bfff:
if this is the case and you are using D+M to adjust then maybe the restore was only a partial success (might haveto dig up some stuff from a full nand backup avalible at trisoft.

If beta1 also used the zaurushw thing and you are editing the right file ... hum intresting I'd like to investigate further.

If nether of these situations suits then you're probably doing something wrong ;-)
[div align=\"right\"][a href=\"index.php?act=findpost&pid=163605\"][{POST_SNAPBACK}][/a][/div]

Actually, I'm talking about r198, so sorry if that wasn't clear.

Thanks...I'll look into it.

louigi600 · « **Reply #10 on:** June 23, 2007, 03:23:18 pm »

Oh ... then /etc/sysconfig/zaurushw is the place to look ;-)

Capn_Fish · « **Reply #11 on:** June 23, 2007, 04:08:56 pm »

I just tried messing around with zaurushw, and now my screen is ghost-free !!!

Thank you!!!

News:

Author Topic: "ghosting" Caused By R121? (Read 3747 times)