Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mickh

Pages: [1]
1
Security and Networking / Enfora Gsm110 Gprs Connection Problems
« on: October 25, 2006, 05:44:21 pm »
Output from netstat -rn

Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
10.0.0.1        0.0.0.0         255.255.255.255 UH       40 0          0 ppp0
0.0.0.0         10.0.0.1        0.0.0.0         UG       40 0          0 ppp0

Output from ifconfig -a

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

ppp0      Link encap:Point-to-Point Protocol  
          inet addr:151.81.7.66  P-t-P:10.0.0.1  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1500  Metric:1
          RX packets:9 errors:4 dropped:0 overruns:0 frame:0
          TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:3
          RX bytes:108 (108.0 b)  TX bytes:130 (130.0 b)


cat /etc/resolv.conf gives

# Domain name searches will fail until you point this to a real DNS server.
nameserver 212.245.255.2
nameserver 193.70.192.25


I tried ping again and sometimes it works.
e.g. ping google.com gave me a few responses but generally I get between
85% and 100% packet loss

I am trying to use the built-in NetFront browser. How do I check Proxy Settings
for this and what should they be?

The ability to connect is somewhat erratic. On some attempts I get the following
(last few lines only).

rcvd [IPCP ConfAck id=0x2 <addr 151.81.6.224> <ms-dns1 212.245.255.2> <ms-dns3 193.70.192.25>]
sent [IPCP ConfReq id=0x2 <addr 151.81.6.224> <ms-dns1 212.245.255.2> <ms-dns3 193.70.192.25>]
Timeout 0x20084bc:0x203b6a0 in 3 seconds.
rcvd [IPCP ConfAck id=0x2 <addr 151.81.6.224> <ms-dns1 212.245.255.2> <ms-dns3 193.70.192.25>]
sent [IPCP ConfReq id=0x2 <addr 151.81.6.224> <ms-dns1 212.245.255.2> <ms-dns3 193.70.192.25>]
Timeout 0x20084bc:0x203b6a0 in 3 seconds.
rcvd [LCP TermReq id=0x1 cf 03]
LCP terminated by peer (M-O^C)
Untimeout 0x20084bc:0x203b6a0.
Timeout 0x20084bc:0x203b440 in 3 seconds.
sent [LCP TermAck id=0x1]
Modem hangup
Untimeout 0x20084bc:0x203b440.
Connection terminated.



but if I try enough times I eventually get this..

sent [IPCP ConfNak id=0xa <addr 10.0.0.1>]
rcvd [IPCP ConfReq id=0xb <addr 212.245.41.43>]
ipcp: returning Configure-REJ
sent [IPCP ConfRej id=0xb <addr 212.245.41.43>]
rcvd [IPCP ConfReq id=0xc]
ipcp: returning Configure-ACK
sent [IPCP ConfAck id=0xc]
Untimeout 0x20084bc:0x203b6a0.
ipcp: up
local  IP address 151.81.7.66
remote IP address 10.0.0.1
primary   DNS address 212.245.255.2
secondary DNS address 193.70.192.25
Script /etc/ppp/ip-up started (pid 776)
Script /etc/ppp/ip-up finished (pid 776), status = 0x0


Thanks for your help,

Mick.

2
Security and Networking / Enfora Gsm110 Gprs Connection Problems
« on: October 24, 2006, 04:07:36 pm »
Hi all,

I am trying to use an Enfora GSM0110 cf gprs card with my zaurus C3000 (sharp rom converted to English by restoring Trisoft backup, kernel 2.4.20).

After much trial and error (days!!) I finally seem to have a connection from the terminal but I have to run pppd call gprs twice. The first attempt always fails.

The final line of the output says:-

.
.
Script /etc/ppp/ip-up finished (pid 821), status = 0x0

and ifconfig output seems positive

ppp0   Link encap:Point-to-Point Protocol
          inet addr:151.81.1.33 ...etc.
          Up POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
.
.
etc.

Also credit is taken from my sim card when I do this!!



However, there is no response to any ping commands (100% loss) and trying to access the internet via the browser gives the message 'no connection to the network. Connect now?'

The same scripts work with this card and the same sim on my laptop under linux with no problems.

Anyone had similar problems or know how I can investigate further?

Thanks for any help.

I can post the full output/scripts etc. here if it helps.

Mick

3
Security and Networking / Enfora Gsm110 Gprs Connection Problems
« on: October 24, 2006, 03:43:41 pm »
speculatrix,

If you are still watching this post, I have an enfora GSM110 which I managed to get to connect (but I still have problems). See my new post - Enfora GSM110 gprs connection problems.

Mick.

4
C1000/3x00 General discussions / Can't Get Mplayer/kino2 Working With C3100
« on: October 10, 2005, 05:14:05 pm »
I installed kino2 exactly as described on Cresho's page (see link from his post above). It worked first time with no problems on my zaurus c3000 with standard rom.

I created a movie also basically as described on Chresho's site but I used DVDshrink instead of DVDdecrypter. A one and a half hour movie needs about 220MB.

Thanks Cresho,

Mick.

5
Accessories / Zgps And Billionton Cf Gps Card
« on: July 05, 2005, 03:36:27 pm »
I have a zaurus sl c3000 with a billionton CF GPS card. When I start zGPS I get the following error:-

writeMemoryTrack:: error 13 opening

Sometimes zGPS also freezes at this point (but not always)

Does anyone know the meaning and solution?

Anyone know how to access the data coming from the CF card in one of my own programs (read the CF interface in some way?).

Thanks for any help,

Mick

6
Personal Java/Jeode/J2ME Personal Profile / Where To Find Jeode For Sl C3000
« on: June 19, 2005, 03:59:18 pm »
I meant to say jeode in the post. Are there any other recommended jvms for zaurus?

7
Personal Java/Jeode/J2ME Personal Profile / Where To Find Jeode For Sl C3000
« on: June 19, 2005, 03:58:26 pm »
I have just bought a zaurus sl c3000 (japanese). It seems it does not come with a java runtime pre-installed. Where can I find the latest version for download?

Thanks,

Mick.

8
Security and Networking / Ftp Not Working
« on: June 12, 2005, 03:50:35 pm »
Quote
Don't use ftp or telnet, both of them send passwords as plain text! Use ssh and sftp/scp instead.

Stu
[div align=\"right\"][a href=\"index.php?act=findpost&pid=83079\"][{POST_SNAPBACK}][/a][/div]

My question is about ftp. If I wanted to use ssh/scp I would. (I have no passwords on my zaurus anyway so sending them as plain text does not matter!).

9
Security and Networking / Ftp Not Working
« on: June 06, 2005, 02:53:50 pm »
I have recently bought a zaurus SL-C3000.

I can telnet to my zaurus from my windows XP box (using cygnus shell) and browse the zaurus directories.

However, ftp from the windows box does not work. I try the following:-

ftp 192.168.129.201

and get the following:-

Connected to 192.168.129.201
Connection closed by remote host.

It seems that the connection is initially established but then the zaurus closes the connection.

I saw someone else posted the same problem in another group but there was no solution posted.

Anyone help?

thanks,

MickH

Pages: [1]