Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - yanyan

Pages: [1]
1
OpenZaurus/Opie/Qtopia / Bitbake For Single File-----openvpn
« on: December 04, 2006, 12:35:55 pm »
I want to compile the openvpn for my SL5500. I install the OE bitbake for this purpose. When I run bitbake everything is all right.
Code: [Select]
DL_DIR="/stuff/source"
BBFILES:="/stuff/org.openembedded.dev/packages/*/*.bb"

TARGET_OS="Linux"
TARGET_ARCH="arm"
TARGET_FPU="soft"

MACHINE="collie"
#DISTRO= "openzaurus-3.5.4"
DISTRO="openzaurus-unstable"
#DISTRO_VERSION = "3.5.4"

INHERIT = "package_ipk"
IMAGE_FSTYPES= "jfffs2 tar"
BBINCLUDELOGS="yes"

PREFERRED_PROVIDERS="virtual/qte:qte virtual/libqpe:libqpe-opie"
PREFERRED_PROVIDERS+= "virtual/libsdl:libsdl-qpe"
ASSUME_PROVIDED += "virtual/arm-linux-gcc-2.95"
I use DISTRO="openzaurus-unstable" because under /stuff/org.openembedded.dev/conf/dist/ there is only openzaurus-unstable.conf but not the openzaurus-3.5.4.conf.  am I right?

The first time I run
bitbake -b /stuff/org.openembedded.dev/packages/openvpn/openvpn_2.0.2.bb

It generates the ipk under /stuff/build/conf/tmp/deploy. I copy to my Z, but when I use ipkg to install it responds that invalid image. How can I solve this?

so I modidied the local.conf a bit, using DISTRO= "openzaurus-3.5.4" instead of
DISTRO="openzaurus-unstable" and I also find openzaurus-3.5.4.conf from the internet and put it into the path.

but the second time I bitbake openvpn it fails. error message is

Code: [Select]
NOTE: package openvpn-2.0.2-r0: task do_configure: started
NOTE: SITE files /stuff/org.openembedded.dev/site/endian-little /stuff/org.openembedded.dev/site/arm-linux
ERROR: function do_configure failed
ERROR: log data follows (/stuff/build/conf/tmp/work/arm-linux/openvpn-2.0.2-r0/temp/log.do_configure.4100)
| /stuff/build/conf/tmp/work/arm-linux/openvpn-2.0.2-r0/temp/run.do_configure.4100: line 565: automake: command not found
| /stuff/build/conf/tmp/work/arm-linux/openvpn-2.0.2-r0/temp/run.do_configure.4100: line 566: automake: command not found
NOTE: Task failed: /stuff/build/conf/tmp/work/arm-linux/openvpn-2.0.2-r0/temp/log.do_configure.4100
NOTE: package openvpn-2.0.2-r0: task do_configure: failed
ERROR: TaskFailed event exception, aborting
NOTE: package openvpn-2.0.2: failed
ERROR: Build of 'openvpn' failed
Build statistics:
  Attempted builds: 1
  Failed builds: 1

Thanks a lot, can someone gives me suggestions?

2
5x00 Hardware / Pretec Bluetooth Card Recognized But Can't Work
« on: December 04, 2006, 12:15:44 pm »
My bluetooth card for SL5500 is pretec BT 2000E(CF stocket). The problem is that when I insert it into the stocket, it can be recognized.

But when I use the command "hcitool dev" to check the MAC address, there is no devics.

I had put the bt950_cs.o into the correct path. and reboot the machine again and again. It still doesn't work.

Can some one give me some hits?


my situation is similar with the article describe before, but using this method still can't solve my problem.


https://www.oesf.org/forums/lofiversion/ind...php?t20488.html


Thanks

Pages: [1]