Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - yanyan

Pages: [1]
5x00 Hardware / Pretec Bluetooth Card Recognized But Can't Work
« on: December 05, 2006, 03:26:40 pm »
hm, well, your card looks like it's working.

I've been looking at my config files in /etc/pcmcia and /etc/hotplug and can't find anything that seems to match.

My guess is that you should be able to hack an entry into your /etc/pcmcia/serial.conf to bind a serial device to it... something like

card "Pretec BT2000E Bluetooth PC/CF Card"
    manfid: 0x022d, 0x2000
    bind "serial_cs"

eject the card and "HUP" the cardmanager (or reboot).

sorry, that's my best guess.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=148088\"][{POST_SNAPBACK}][/a][/div]
Code: [Select]
In my machine there is no /etc/pcmcia/serial.conf but only /etc/pcmcia/bluetooth.conf and in bluetooth.conf I found some similar link

device "bt950_cs"
  class "bluetooth" module "bt950_cs"

card "Pretec BT2000E Bluetooth Card"
  version "Pretec", "BT2000E"
  bind "bt950_cs"

there is no specified like manfid: 0x022d, 0x2000. Do I need to tell the machine this, but which file I should add this line. in bluetooth.conf, there no similar line exit for other brand bluetooth card.

5x00 Hardware / [sl5500] Eth Over Usb Connection
« on: December 04, 2006, 05:35:15 pm »
what do you mean re-work?

if it works for a few minutes, later you need to excute the ifconfig usb0 ......... again. Maybe your Z fall in sleep. once the machine in the suspend status the usb connection will break down.

5x00 Hardware / Pretec Bluetooth Card Recognized But Can't Work
« on: December 04, 2006, 05:25:27 pm »
Code: [Select]
root@collie:~# cardctl status
Socket 0:
  3.3V 16-bit PC Card
  function 0: [ready], [bat dead], [bat low]
Socket 1:
  no card

Code: [Select]
Socket 0:
  product info: "Pretec", "BT2000E", "Bluetooth PC/CF Card"
  manfid: 0x022d, 0x2000
  function: 2 (serial)
Socket 1:
  no product info available

Code: [Select]
PRODID_3="Bluetooth PC/CF Card"

Thanks a lot

OpenZaurus/Opie/Qtopia / Bitbake For Single File-----openvpn
« on: December 04, 2006, 05:17:54 pm »

Here is the error message when i use bitbake openvpn

Code: [Select]
NOTE: multiple providers are available (glibc, glibc-intermediate);
NOTE: consider defining PREFERRED_PROVIDER_virtual/arm-linux-libc-for-gcc
NOTE: multiple providers are available (linux-openzaurus, collie-kernel-24-8, poodle255-kernel-2.4-embedix, collie-kernel-48-16, a780-kernel, corgi-kernel-2.4-embedix, linux-geodegx, collie-kernel-58-6, poodle-kernel-2.4-embedix, shepherd-kernel-2.4-embedix, linux-h1940, ipod, linux-mtx-3, collie-kernel-32-0, linux-omap-2.6, xanadux-un-2.6, linux-h6300-omap1, husky-kernel-2.4-embedix, linux-geodelx, linux-xxs1500, LAB-kernel, collie-kernel-32-32, linux-bast, openzaurus-sa, xanadux-ba-2.6, collie-kernel-64-0, collie-kernel-40-24, collie-kernel-58-6-debug);
NOTE: consider defining a PREFERRED_PROVIDER to match runtime kernel-module-tun
NOTE: build 200612042308: completed
Build statistics:
  Attempted builds: 0

should I specify the right library for that?

OpenZaurus/Opie/Qtopia / Bitbake For Single File-----openvpn
« on: December 04, 2006, 02:23:05 pm »
What i build up my OE i use


I think this contains all machines and all distors that OE supports.
Would you give me some link to downlond the the whole Metas.

I just check the
it contains the openvpn.

But anyway i still need to compile one route protocol for my Z, I need to compile the single file anyway. What should I do?

As my understanding I should create my own .bb file first and then still use "bitbake -b"

Now I am using the bitbake openvpn. But I saw one line
Code: [Select]
for my sl5500 it only runs kernel 2.4, I think it should be the invalid image again.

But anyway. I will wait and try.

OpenZaurus/Opie/Qtopia / Bitbake For Single File-----openvpn
« on: December 04, 2006, 12:35:55 pm »
I want to compile the openvpn for my SL5500. I install the OE bitbake for this purpose. When I run bitbake everything is all right.
Code: [Select]


#DISTRO= "openzaurus-3.5.4"

INHERIT = "package_ipk"
IMAGE_FSTYPES= "jfffs2 tar"

PREFERRED_PROVIDERS="virtual/qte:qte virtual/libqpe:libqpe-opie"
PREFERRED_PROVIDERS+= "virtual/libsdl:libsdl-qpe"
ASSUME_PROVIDED += "virtual/arm-linux-gcc-2.95"
I use DISTRO="openzaurus-unstable" because under /stuff/ there is only openzaurus-unstable.conf but not the openzaurus-3.5.4.conf.  am I right?

The first time I run
bitbake -b /stuff/

It generates the ipk under /stuff/build/conf/tmp/deploy. I copy to my Z, but when I use ipkg to install it responds that invalid image. How can I solve this?

so I modidied the local.conf a bit, using DISTRO= "openzaurus-3.5.4" instead of
DISTRO="openzaurus-unstable" and I also find openzaurus-3.5.4.conf from the internet and put it into the path.

but the second time I bitbake openvpn it fails. error message is

Code: [Select]
NOTE: package openvpn-2.0.2-r0: task do_configure: started
NOTE: SITE files /stuff/ /stuff/
ERROR: function do_configure failed
ERROR: log data follows (/stuff/build/conf/tmp/work/arm-linux/openvpn-2.0.2-r0/temp/log.do_configure.4100)
| /stuff/build/conf/tmp/work/arm-linux/openvpn-2.0.2-r0/temp/run.do_configure.4100: line 565: automake: command not found
| /stuff/build/conf/tmp/work/arm-linux/openvpn-2.0.2-r0/temp/run.do_configure.4100: line 566: automake: command not found
NOTE: Task failed: /stuff/build/conf/tmp/work/arm-linux/openvpn-2.0.2-r0/temp/log.do_configure.4100
NOTE: package openvpn-2.0.2-r0: task do_configure: failed
ERROR: TaskFailed event exception, aborting
NOTE: package openvpn-2.0.2: failed
ERROR: Build of 'openvpn' failed
Build statistics:
  Attempted builds: 1
  Failed builds: 1

Thanks a lot, can someone gives me suggestions?

5x00 Hardware / Pretec Bluetooth Card Recognized But Can't Work
« on: December 04, 2006, 12:15:44 pm »
My bluetooth card for SL5500 is pretec BT 2000E(CF stocket). The problem is that when I insert it into the stocket, it can be recognized.

But when I use the command "hcitool dev" to check the MAC address, there is no devics.

I had put the bt950_cs.o into the correct path. and reboot the machine again and again. It still doesn't work.

Can some one give me some hits?

my situation is similar with the article describe before, but using this method still can't solve my problem.


Pages: [1]