Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - m3xican

Pages: [1]
1
Angstrom & OpenZaurus / Upgrade Packages Problem...
« on: July 31, 2005, 03:03:19 pm »
Hi,

I have just reflashed my Z SL-5500 with the last OZ release (zImage 64-0 and Opie 1.2) and then I have tried to follow the "Howto get r21 kernel on collie" news on OZ website, but ipkg stalls during upgrade procedure.

Flash works fine and all the modules are upgraded to r21 version, the problem is raised during libqte2 upgrade, the last thing that ipkg print out is:
Quote
upgrading libqte2 on root from 2.3.10-r12 to 2.3.10-r14...
downloading http://www.openzaurus.org/official/unstabl...-r14_collie.ipk

I have tried to upgrade under opie konsole and under Z console (logout from opie), obtaining the same result.

What could I do now?  

2
Angstrom & OpenZaurus / Gpe Or Opie?
« on: June 23, 2005, 06:09:13 pm »
Hi,
I have a Z SL-5500 and I have to flash it again, so I should choose between OPIE and GPE, suggestions on what is better and why?

Thanx

3
Italy / Problema Connessione Usb/linux
« on: June 20, 2005, 04:49:40 am »
Salve, ho postato già questa richiesta di aiuto in 5x00 General discussions, ma la riposto qui in italiano per aumentare la speranza che qualcuno mi aiuti...

Il problema è il seguente, in pratica utilizzando il cradle usb dello Z non riesco a connettermi nè dal pc allo Z nè dallo Z al pc (o a internet).
L'unica cosa che sono riuscito ad ottenere è pingare lo Z dal pc (divertente, ma poco utile...  ).

Lo Z è riconosciuto perfettamente da hotplug (utilizzo Linux Slackware 10.0), e su di esso gira un sshd, funzionante (ci si riesce a connettere dallo Z stesso), ma non accedibile dall'esterno.
Ogni tentativo di connessione mi viene rifiutato, eppure sullo Z ho configurato sia inetd.conf che hosts.allow per accettare richieste da chiunque.
Ovviamente sullo Z sono aperte anche le porte per effettuare FTP (4242, 4243), ma ogni tentativo di connessione porta sempre allo stesso fallimento...  

Qualcuno può aiutarmi?

4
Italy / Salve
« on: June 18, 2005, 07:16:15 am »
Salve,

da pochi giorni sono possessore di uno Z SL-5500, attualmente ho un pò di problemi di configurazione, ma spero di risolverli presto (se qualcuno mi vuole aiutare può partecipare alla discussione linkata) e di utilizzare a pieno questo fantastico PDA.

Posto per salutare la comunità (che purtroppo mi sembra molto esigua...) e per chiedere se in italia esiste un qualche sito di riferimento per lo Z.

A presto.

5
5x00 General discussions / Usb/linux Connection Problems...
« on: June 18, 2005, 07:11:01 am »
Hi... I'm loosing my mind, so I hope that someone here could help me!  

I have a SL-5500 with Opie 0.9.3-snapshot - OZ 3.2 - kernel 2.4.6-rmk1-np2-embed.

I can't connect to my Z from Linux (Slackware 10.0) neither connect to my pc from Z.

My Linux box recognizes the Z when I put it into the cradle:
Quote
hub.c: new USB device 00:0d.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x4dd/0x8004) is not claimed by any active driver.
usb.c: registered new driver acm
acm.c: v0.21:USB Abstract Control Model driver for USB modems and ISDN adapters
usb.c: registered new driver usbnet
usb0: register usbnet usb-00:0d.0-1, Sharp Zaurus SL-5x00

I set the usb interface with:
Quote
ifconfig usb0 192.168.129.201 netmask 255.255.255.255 up
(note: if I set usb0 to 192.168.129.1 how I have read on several HOWTO nothing works )
obtaining:
Quote
usb0      Link encap:Ethernet  HWaddr 46:8F:DE:4E:3A:4E
          inet addr:192.168.129.201  Bcast:192.168.129.255  Mask:255.255.255.255
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0   TX bytes:0 (0.0
and I can ping the Z
Quote
bash-2.05b# ping 192.168.129.201
PING 192.168.129.201 (192.168.129.201) 56(84) bytes of data.
64 bytes from 192.168.129.201: icmp_seq=1 ttl=64 time=0.060 ms
64 bytes from 192.168.129.201: icmp_seq=2 ttl=64 time=0.050 ms

--- 192.168.129.201 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 999ms
rtt min/avg/max/mdev = 0.050/0.055/0.060/0.005 ms
But I can't have any kind of connection on it.

On the Z is running a ssh daemon, Z can connect to itself (at least this...), but no connection is possible from the pc.

I have followed the connecting to a linux pc over USB HOWTO, but nothing (except ping from pc) works...

Any suggestions?

Pages: [1]