Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - climber

Pages: 1 2 [3] 4
31
Zaurus - pdaXrom / Wifi-radar Not Working
« on: June 26, 2007, 04:33:29 am »
Hi,

I've Meanies pdaXii13 v5.4.7 on my SL-C3100 installed and want to use wifi-radar. To get up to date I installed the newest version of:

- wifi_radar_1.9.8_2_armv5tel.ipk
- wpa_supplicant_0.4.7_2_armv5tel.ipk

The I'm not sure whether this is the right way or not so I created inside wifi-radar a new profile with the following setting:

Network Name: bitbuilder
Wifi Options:   Mode= auto |  Channel = Auto
Use WPA:  Driver=ipw
Manual Network configuration:
  IP: 10.0.0.10
  Netmask: 255.255.255.0
  Gateway: 10.0.0.1
  Domain:  bitbuilder.com
  DNS:  216.251.101.72
  DNS:    10.0.0.1
Connectin Command:   After = ifconfig eth2 mtu 1430

I'm not sure wehter these are the right settings. When I do connect to this settings I can't see any wlan although there are a lot of wlans here!

Do I have to do settings at System --> Lan&Wifi  like for kismet or Wellenreiter?

Please help me to get this working!    

Thanks
climber

32
Zaurus - pdaXrom / Pdaxii13 - Fn3/4 (brightness)
« on: June 22, 2007, 03:32:45 am »
Hi,

I'm sure that when I press the Super-Key and 3/4 I can decrease and increase the brightness. This functionallity don't work anymore and I don't know why.

I checket the setting at the pdaXii13-config tool and the 'Sticky Keys' are enabled.

Meany or anyone else  do you have a idea why this don't work anymore?



Thanks
climber

SL-C3100 pdaXii13 v5.4.6#


P.S I'm back on the road again and your installation instruction for akita worked perfect!

33
Zaurus - pdaXrom / Crash - Pdaxii13
« on: June 19, 2007, 11:02:26 am »
Hi,

I only want to do a fsck on /dev/hda1 so i used the pdaXi13 v5.4.6 config-tool to activate the "Maintenance Mode".

After reboot I got the following message:

Warning:  unable to open  an initial console
Kernel panic: Attempted to Koll init!    

I used the update menue to get a shell to type in:  fsck /dev/hda1
At the end there were errors and again "Kernel panic!"

Ok ...ggggrrrr!!!!

Restoring a Nand-Backup failed. So I decided to start from the beginning:

1.) Install pdaXrom beta3
2.) copy Meanies pdaXii13 v5.4.6 data to cf
3.) Install the kernel and bootloader TWICE, once before and one after installing the hdimage
4.) After this reboot I got the same error message as above!!!!


I hope that anyone can help me!!!    

Thanks
climber

34
Zaurus - pdaXrom / Pdaxii13 Build5.4.7 Available?
« on: June 19, 2007, 06:42:11 am »
Meanie,

you mentioned your newest version 5.4.7 on this link
http://www.tyrannozaurus.com/feed/pdaXii13/tmp/   but I could only find the download for 5.4.6 [hdimage-custom.tgz]?

Is this the new or the old one?

Regards
climber

35
Zaurus - pdaXrom / Ppt/pps Viewer
« on: June 14, 2007, 07:10:34 am »
Does anybody know whether there exists a ppt/pps viewer for pdaXrom like under sharp/cacko rom?

This would be very nice!  

Thanks
climber

36
Zaurus - pdaXrom / Pdaxii13 + Icewm --> Keyboard Shortcuts?
« on: May 09, 2007, 02:30:37 am »
Hi,

I'm using the pdaXii13 build 5.4.1 version on my SL-C3100 and it looks pretty good. Icewm is the default window manager and I like it more and more.

Does anybody know any keyboard shortcuts with these windomaker like meanie
discribed in his documentation for pdaXii13

anything like that:

Alt+0 = MaximizeFull
Alt+5 = UnmaximizeFull
Alt+9 = Iconify
Alt+8 = Resize
Alt+7 = Move
Alt+4 = Close

I tried many shortcuts but this upper and the other of meanies doc don't work. Maybe they are complete different or not set yet.

I hope someone can help me?

Tanks,
climber

37
Zaurus - pdaXrom / Pdaxii13 Upgrade To New Version
« on: April 23, 2007, 11:12:37 am »
Hi,

I've meanies pdaXii13 5.3.4 version installed [full-image]. Now I want to upgrade to his newest one 5.3.6.

I've a SL-C3100 so which data do I need to upgrade to it. I thought I have to copy the hdimage-custom.tgz/updater.sh/updater-tools.bin/initrd.bin/hdimage-full.tgz to my CF-card. But in the boot-menue [reboot and press 'OK'] I can't find a upgrade buttom!

Who knows which data I need to upgrade my zaurus with pdaXii13 v.5.3.4 to v.5.4.6.

Thanks
climber  

38
Zaurus - pdaXrom / Pdaxii13 - 'add German "umlaute"
« on: March 30, 2007, 07:10:47 am »
Hi,

how can I add the German "Umlaute" (ö,ü,ä) to the version 5.3.3 of pdaXii13?


Regards
climber

39
Zaurus - pdaXrom / Symlink /home To /mnt/ide2/home
« on: March 05, 2007, 03:48:01 am »
Hi,

I want to create the following symlink:

/home is a symlink of /mnt/ide2/home


What I did:

- copy the whole /home directory to /mnt/ide2/home
- Create symlink:  ln -s /mnt/ide2/home/ /home


When I do a reboot I get the following error message:

Module dependencies:     OK
mount: special device /hom/user  does not exist

I think I did not all entries but I don't know where and which to do to fix this problem.

Can anybody help me?


Thanks
climber

SL-C3100 with pdaXrom beta3

40
Zaurus - pdaXrom / Resize The Partitions Of The Microdrive
« on: February 23, 2007, 05:40:30 am »
I have pdaXrom beta3 on my SL-C3100 installed. Now I want to setup my partitions as Chero did before.


- big root (121Mb)    --> Done
- swap on SD (128Mb)  --> Done
- ide(1) : 1Gb ext2 to install apps  
- ide2 : 2Gb ext2 for data and compiling
- ide3 : 1Gb fat exchange data with my Win2K

How can I scale down my big 4GByte partition to 1GB and make the two others bigger?

Regards
climber

41
Software / Microemacs - Hot Keys
« on: September 21, 2006, 07:34:14 am »
Hi,

I have installed the microemac to my SL-C3100 Cacko 1.23 zaurus from this link:

http://zaurus.geeek.org/Cacko/feed/microemacs_1.4-1_arm.ipk

When I start the emac from the shell I see a green menu bar at the top. With which hot key can I change to this menu. I tried many combinations with "alt + f" or "FN +f" but all failed.

regards.
climber

42
General Discussion / Mount A Cf 4 Gbyte Card
« on: August 25, 2006, 04:04:17 am »
I have bought a CF 4GB Card from SanDisk. When i put the card into the cf slot then it seems that the new card "New Card: ATA/IDE Fixed Disk" is identified and possibly mounted. But when I got to "/mnt/cf" there is nothing mounted "NotAvailable". I see the new card only at the "Setting" tab [System Info / Devices / CF Slot / Socket 0 / ...].

What has to be done to get this 4 GByte CF card working. When I take a look at the signature of some members  they have a 4GByte cf card working  (for example Meanie with 4 GByte cf card from Kingston).

So I think it should work however I don 't know what I have to do. I hope someone can help me.

Thanks
climber

SL-C3100 & Cacko 1.23

43
General Discussion / Cf 4 Gbyte Too Fast For Zaurus?
« on: August 21, 2006, 03:02:00 am »
I would buy a 4 GByte Compact Flash Card from SanDisk [Extreme III]. This card isn`t very cheap. Therefore I wan`t to know if the zaurus is able to support this very fast card. Maybe the zaurus can 't process this speed and uses only a    fractional amount of this. If this it true I would buy a cheaper card.

Here are the data from the card:

Datarate read [KB/s]:  20480
Datarate write [KB/s]:  20480


Could anybody help me to check this?

Thanks
climber

Zaurus SL-C3100 + Cacko 1.23

44
X/Qt / Pdaxqtrom 0.8.0 - Too Small Representation
« on: August 17, 2006, 03:23:47 am »
I 've just installed Meanies pdaXQtrom - ver 0.8.0. When I start some applications I need a magnifier to decode the font because it 's very small. When I take a look to the snapshot of the  Application "Planner" from http://pdaxqtrom.thegrinder.ws/files/pdaxqtrom.html" I can see the font very good. It seems that it 's all displayed larger.

Do I have to install more or other fonts? Where can I do such settings to the design size of the applications.

Thanks
climber

45
Software / Supertux - Libsdl Error
« on: July 25, 2006, 07:15:04 am »
Hi,

I 've installed the game SuperTux on my SL-C3100 & Cacko 1.23 as follows:


supertux_0.1.2-2_arm.ipk
libSDL-image_1.2.3-0_arm.ipk
libSDL-mixer_1.2.6-zports-1_arm.ipk

Then ran these commands:

ln -s /usr/QtPalmtop.rom/lib/libpng12.so.0.1.2.5 /usr/lib/libpng.so.3
ldconfig


When I want to start this application I got the following error:


#supertux
suptertux: error while loading shared libraries: libSDL-1.2.so.0: cannot load shared object file: No such file or directory



What 's going wrong? Could someone help me to solve this problem?


Thanks
climber

Pages: 1 2 [3] 4