Ajzaurususb 0.3.2 Update

[gojira]

I have tested the AJZaurusUSB driver that I compiled, packaged and was uploaded to Dsitri. It installs without problems and is fully functional. My MacBook Pro "sees" my Collie and my Collie barks at my MacBook.

Chris--
[div align=\"right\"][a href=\"index.php?act=findpost&pid=135253\"][{POST_SNAPBACK}][/a][/div]

I've installed the package and the interface shows green when the z is connected but I can't ping either, and get "no route to host" and "host is down" from the mac

[freizugheit]

What is the IP of the Mac shown under System Preferences/Network/Bulit-in Ethernet/TCP/IP ?

Which Zaurus is in use?

[gojira]

I removed the kernel extension and now after I reinstall and reboot it doesn't show up at all...

[gojira]

I removed the kernel extension and now after I reinstall and reboot it doesn't show up at all...
[div align=\"right\"][a href=\"index.php?act=findpost&pid=137453\"][{POST_SNAPBACK}][/a][/div]

ok, so now I loaded the extension manually (not sure if that was needed but if I try it again it says it's already loaded, so it wasn't loaded automatically, but maybe it just loads it on first use...) and got the interface to appear by changing the priority order of interfaces in the port config list (it just appeared when I moved one of the others), then configured it, and now it's back in the status list after connecting the z (but the currently unused interfaces aren't in that list -- petty sure they were originally)

so ifconifg on the mac says...

en2: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        inet6 fe80::3630:30ff:fe30:3000%en2 prefixlen 64 scopeid 0x8
        inet 192.168.129.1 netmask 0xffffff00 broadcast 192.168.129.255
        ether 34:30:30:30:30:00
        media: autoselect (10baseT/UTP <full-duplex>) status: active
        supported media: none autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 100baseTX <half-duplex> 100baseTX <full-duplex>

...when the z is connected and nothing about en2 otherwise

the z shows usbd0 up on 192.168.129.201 regardless but with a few more packets after connection

mac console has...

Aug  9 22:49:17 sumi mDNSResponder: Repeated transitions for interface en2 (192.168.129.1); delaying packets by 5 seconds

z dmesg has...

net_recv_urb: TOO LARGE urb->actual_length: 63 maxtransfer: 0
net_recv_urb: TOO LARGE urb->actual_length: 127 maxtransfer: 0
NETDEV WATCHDOG: usbd0: transmit timed out
usbd_device_bh: usbd_device_bh: no urb_sent function
netproto_recv: not registered: state: 0
netproto_recv: not up net_dev->flags: 1002

...then lots more watchdog timeouts

same problems pinging as before

I no longer have access to the linux box I used to use for this, so not sure if the z messages are normal, and don't have another ethernet-over-usb device to connect to the mac to see if that message is typical either, so if anyone has any ideas, please let me know

thanks

[gojira]

[a href=\"index.php?act=findpost&pid=137938\"][{POST_SNAPBACK}][/a]

I removed extension and the receipt and reinstalled and the other interfaces came back in the status and the interface showed green when the z was connected but still no ping and no route.  And now the interface no longer shows green and there's no interface listed under the z in the system profiler...

[chrisl]

[a href=\"index.php?act=findpost&pid=137938\"][{POST_SNAPBACK}][/a]

I removed extension and the receipt and reinstalled and the other interfaces came back in the status and the interface showed green when the z was connected but still no ping and no route.  And now the interface no longer shows green and there's no interface listed under the z in the system profiler...
[div align=\"right\"][a href=\"index.php?act=findpost&pid=138988\"][{POST_SNAPBACK}][/a][/div]

Here is a copy of my system profiler output:

SL-5500:

  Removable Media:   No
  Detachable Drive:   Yes
  BSD Name:   en2
  Version:   0.00
  Bus Power (mA):   500
  Speed:   Up to 12 Mb/sec
  Manufacturer:   Sharp
  OS9 Drivers:   No
  Product ID:   0x8004
  Serial Number:   400002000001
  Vendor ID:   0x04dd

So it does work. I had unistalled the originally compiled extension and installed the package I compile and it still worked. Be sure you are using the Intel compiled version and not ppc version. Otherwise, you might want to compile it yourself as I had done.

It would be interesting if anyone else is having this issue.

Chris--

[gojira]

So it does work. I had unistalled the originally compiled extension and installed the package I compile and it still worked. Be sure you are using the Intel compiled version and not ppc version. Otherwise, you might want to compile it yourself as I had done.

It would be interesting if anyone else is having this issue.

Chris--
[div align=\"right\"][a href=\"index.php?act=findpost&pid=139086\"][{POST_SNAPBACK}][/a][/div]

Thanks.  I've built the module too now and it behaves the same -- the interface is there but I can't ping either end from the other and the z logs transmit timeouts.  If no one else is having this problem the next step is to reflash the z (which has been getting more and more flakey lately (although usbd0 was working ok to my old linux box))...

[chrisl]

So it does work. I had unistalled the originally compiled extension and installed the package I compile and it still worked. Be sure you are using the Intel compiled version and not ppc version. Otherwise, you might want to compile it yourself as I had done.

It would be interesting if anyone else is having this issue.

Chris--
[div align=\"right\"][a href=\"index.php?act=findpost&pid=139086\"][{POST_SNAPBACK}][/a][/div]

Thanks.  I've built the module too now and it behaves the same -- the interface is there but I can't ping either end from the other and the z logs transmit timeouts.  If no one else is having this problem the next step is to reflash the z (which has been getting more and more flakey lately (although usbd0 was working ok to my old linux box))...
[div align=\"right\"][a href=\"index.php?act=findpost&pid=139920\"][{POST_SNAPBACK}][/a][/div]

Actually, I have not been able to talk to my Z through the usb. My mac acknowledges the Z is there, will tell me when it is plugged in, but the they will not speak to each other. It is possible because my Z is an ext2 volume, but I doubt it. I have tried both samba and ftp. My mac will acknowledge that there is a samba volume, but will say it is a format that cannot be read. So, I generally use a card reader. I have been told that macs will communicate via wifi as well, but I have not tried yet.

Chris--