I have a full sized CD-ROM installed in a USB external enclosure.
TOSHIBA Model: CD-ROM XM-6202B Rev: 1110
Type: CD-ROM ANSI SCSI revision: 02
This is an older CD-ROM (32x)
I want to get this one working before I plunk down $149.95 for a Slim external USB DVD/CD-ROM drive.
It does work in Windows, I tried it.
C3100 with Cacko 1.23 Lite
Installed these:
isofs-modules-2.4.20_1.23-lite-1_arm.ipk
udf-modules-2.4.20_1.23-lite-1_arm.ipk
I have 4 USB modules installed also:
usb-network-modules-2.4.20_1.23--lite-1_arm.ipk
usb-serial-modules-2.4.20_1.23-lite-1_arm.ipk
usb-storage-modules-2.4.20_1.23--lite-1_arm.ipk
libusb_1.1.8_arm.ipk
I also have "cdrtools-2.01.tar.gz" but am not sure where to install this.
I have followed several instructions to get my CD-ROM drive to mount on my C3100, but it always fails.
I have tried a Data CD. (A CD that I made with directories full of programs and data)
I tried an mp3 only CD. (A CD with 89 mp3s in the root directory)
I decided to use a "pressed" CD from a known manufacturer.
I used Meanie's instructions and Da_Blitz's instructions.
Meanie's instructions:
# su
# mkdir -p /mnt/cdrom
# mount -o ro /dev/scd0 /mnt/cdrom
Da_Blitz's instructions:
# mount /dev/scd0 /mnt/cdrom
I also tried:
# mount /dev/scd0 /mnt/usbstorage
When I issue either command, (Meanie's or Da_Blitz's or /mnt/usbstorage)
I get this:
mount: /dev/scd0 is write protected, mounting read-only
(repeats 6 more times)
mount: /dev/scd0 on /mnt/cdrom failed: Invalid argument
I looked in my /dev folder and I DO have:
cdrom
scd0
I also have cdrom under /mnt
/mnt/cdrom
Below are several lines from dmesg.usbh: monitor_int_hndlr:
usbh: monitor_bh:
usbh: udc_connected: ACTIVE_LOW: 1<7>usbh: monitor_connected: 1
usbh: monitor_load: 4
usbh: monitor_hotplug: agent: usbh interface: monitor action: load
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xfe000000, IRQ 3
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: new USB device -2, assigned address 2
usb.c: USB device 2 (vend/prod 0x4b4/0x6830) is not claimed by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: TOSHIBA Model: CD-ROM XM-6202B Rev: 1110
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi-1 drive
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
VFS: Can't find ext3 filesystem on dev sr(11,0).
VFS: Can't find ext2 filesystem on dev sr(11,0).
cramfs: wrong magic
MINIX-fs: blocksize too small for device.
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 0b:00.
jffs2: attempt to mount non-MTD device 0b:00
SQUASHFS error: Can't find a SQUASHFS superblock on sr(11,0)
VFS: Can't find ext3 filesystem on dev sr(11,0).
VFS: Can't find ext2 filesystem on dev sr(11,0).
cramfs: wrong magic
MINIX-fs: blocksize too small for device.
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 0b:00.
jffs2: attempt to mount non-MTD device 0b:00
SQUASHFS error: Can't find a SQUASHFS superblock on sr(11,0)
VFS: Can't find ext3 filesystem on dev sr(11,0).
VFS: Can't find ext2 filesystem on dev sr(11,0).
cramfs: wrong magic
MINIX-fs: blocksize too small for device.
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 0b:00.
jffs2: attempt to mount non-MTD device 0b:00
SQUASHFS error: Can't find a SQUASHFS superblock on sr(11,0)
#
