Author Topic: How To Do A Pair Up With Mobile Phone  (Read 3510 times)

mullin

  • Newbie
  • *
  • Posts: 42
    • View Profile
How To Do A Pair Up With Mobile Phone
« on: February 25, 2007, 10:07:46 pm »
How do the pair up FROM zaurus?? I can only do it from mobile phone, nokia 9300. I think I miss this part so that I got the following error:

My bluetooth dial-up network shows the following:
1. initializing the modem
2. connecting
3. connecting 0:00:00 [when click "I" icon, i can see the DNS server ip, but ip is 0:0:0:]
4. network disconnect

any ideas? i'm using Anycom CF BT card and the here's my Bluetooth dial-up setting
username:
password:
Phone: *99# or *99***1#
BT device: /dev/rfcomm0
Init string: ATZ
Speed: 115200
Hardware flow control: checked
Flow control: 30sec
Auto-detect routing: checked
Auto-detect name server: checked

abort on (NO CARRIER)
abort on (NO DIALTONE)
abort on (BUSY)
send (ATZ^M)
expect (OK)
ATZ^M^M
OK
-- got it

send (ATDT*99***1#^M)
expect (CONNECT)
^M
ATDT*99***1#^M^M
CONNECT
-- got it

Serial connection established.
using channel 8
Using interface ppp0
Connect: ppp0 <--> /dev/rfcomm0
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x93283a54> <pcomp> <accomp>]
Timeout 0x20084bc:0x203b440 in 3 seconds.
rcvd [LCP ConfReq id=0x0 <auth pap> <mru 1500> <asyncmap 0xa0000>]
lcp_reqci: returning CONFNAK.
sent [LCP ConfNak id=0x0 <auth chap MD5>]
rcvd [LCP ConfRej id=0x1 <magic 0x93283a54> <pcomp> <accomp>]
Untimeout 0x20084bc:0x203b440.
sent [LCP ConfReq id=0x2 <asyncmap 0x0>]
Timeout 0x20084bc:0x203b440 in 3 seconds.
rcvd [LCP ConfReq id=0x1 <auth chap MD5> <mru 1500> <asyncmap 0xa0000>]
lcp_reqci: returning CONFACK.
sent [LCP ConfAck id=0x1 <auth chap MD5> <mru 1500> <asyncmap 0xa0000>]
rcvd [LCP ConfAck id=0x2 <asyncmap 0x0>]
Untimeout 0x20084bc:0x203b440.
rcvd [CHAP Challenge id=0x0 <4953414c4956454e524f434b494e3455>, name = "Elvis"]
ChapReceiveChallenge: using 'BLUETOOTH1136121411' as remote name
sent [CHAP Response id=0x0 <f70dcb8d4fd1d650dd9948ad3304bdcf>, name = "zaurus"]
Timeout 0x200f698:0x203b710 in 3 seconds.
rcvd [CHAP Success id=0x0 ""]
Untimeout 0x200f698:0x203b710.
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <compress VJ 0f 01> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
Timeout 0x20084bc:0x203b6a0 in 3 seconds.
sent [CCP ConfReq id=0x1 <bsd v1 15>]
Timeout 0x20084bc:0x203b7a0 in 3 seconds.
rcvd [IPCP ConfReq id=0x0 <addr 10.6.6.6>]
ipcp: returning Configure-ACK
sent [IPCP ConfAck id=0x0 <addr 10.6.6.6>]
rcvd [LCP ProtRej id=0x0 80 fd 01 01 00 07 15 03 2f]
Untimeout 0x20084bc:0x203b7a0.
rcvd [LCP TermReq id=0x2]
LCP terminated by peer
Untimeout 0x20084bc:0x203b6a0.
CCP: Down event in state 1!
Timeout 0x20084bc:0x203b440 in 3 seconds.
sent [LCP TermAck id=0x2]
Connection terminated.

craigtyson

  • Sr. Member
  • ****
  • Posts: 462
    • View Profile
How To Do A Pair Up With Mobile Phone
« Reply #1 on: February 26, 2007, 05:07:46 am »
I think id depends on the version of the network applet / bluez you have on your Z
With Cacko its done from the bluetooth setup in the network wizard.  using the last tab, you find the device then pair it up.  Im currently using this to access this page.

If it doesnt work post up your ROM version, bluez etc
Cheers
Craig
SL-C1000, Angstrom GPE 2007.12r13
Ambicom WL1100C, SanDisk UltraII 1GB SD
 
Old Faithfull - SL-5500 battery out of the C750 (see below) TKC v1 (New) 1GB SD
Dead - SL-C750, Cacko 1.23 lite (Dropped, very messy!)
Ambicom WL1100C, SanDisk Dead - 1GB SD
Keep your Z on a bungee, you never know.....