Compilation Of Wifi Cf For 3k

[Bombur]

ok 3k users,

I have been going over some of the posts trying to glean which CF cards work and which ones don't.

So far:

Working:
Ambicom WL1100C-CF
Buffalo WLI2-CF-S11G (poor range)
Asus WL-110

not working:
Socket WL6004-322

Anybody care to pipe in and provide corrections/confirmation?  I would really like to know which card I should be buying.  I thought I was going to buy a Socket Wifi card but there seems to be problems with their new ones....There are additional bluez drivers but I don't know if they were installed before trying the new Socket card.

I have also asked c-guys if their SD wifi card will be tested on the 3k.  They said that their intention is to do so but no timings yet.

J.

[wormwood]

I have a Symbol Spectrum24 CF on my SL-C3000 it's currently workin  

[tchen]

I also have a Symbol Spectrum 24 that is not working yet. If anyone knows about
a driver or how to get it working, I would be very grateful.
TC

[wormwood]

tchen, plug in your card then goto Settings -> Network -> Wizard -> detect. Click yes and let it configure it for you. If you continue to have any problems let me know. You and I have the same card and mine is working so it's only a matter of a couple of clicks  

wormwood

[ChrisZ]

I've also got a problem with the Symbol card. It works perfectly in my old 5500.

After I inserted and configured it, there should be the connect button in the network settings. But the button is shown ghosted, I cannot push it. And therefore I can not connect to the Wlan. All Wlan settings are okay, a SMC 2642 works in the C3000.

Accessing the Symbol card via terminal leads to the following results: It's accessible via cardctl ident. I can do cardctl suspend and resume. Even ifconfig eth0 up works if I enter the command immediately after cardctl resume: cardctl resume && ifconfig eth0 up && ifconfig. But after 1 second the device suspends again and nothing works.

Anyone knows what to do?

[wormwood]

ZeeUser said:

To get the Symbol Wireless Networker working with the C3000:

Enter these commands into the terminal:
su
cd /home/etc/pcmcia
vi spectrum.conf

Delete the # from the begining of the second line
Enter a # at the beginning of the third line
Save the changes
Reboot

After trying that out I still had no luck. I deleted all previous wifi devices from list in the network setup then tried Settings -> Network -> Wizard -> detect. Clicked yes all the way through and it worked!

Let me know if the aforementioned doesn't work  

[Bombur]

So far:

Working:
Ambicom WL1100C-CF
Buffalo WLI2-CF-S11G (poor range)
Asus WL-110
Symbol Spectrum 24 (with some work)
SMC 2642

not working:
Socket WL6004-322

I have ordered  an SMC 2642.  We'll see what happens when the 3k and the cf card are introduced to eachother.

J.

[ChrisZ]

Okay, the Symbol Spectrum 24 ... works:

First, you have to follow the ZeeUser-instruction: Edit /etc/pcmcia/spectrum.conf.

Then, you can use the network-settings and install a lan(!), not wlan-card. The spectrum will immediately work (without encryption).

If you want to use encryption, you can insert the nessecary /sbin/iwconfig eth0 enc 0000-0000-0000... -command into the corresponding section of /etc/pcmcia/network.opts, between the {}-parantesis of the start_fn, before the return-statement and followed by a ";". Perhaps you want to add some more options to the iwconfig.

Good luck. :-)

PS: If the Z hangs and the screen disappears: just release the card and reinsert after some seconds. And try again.

[FRH]

I have Linksys WCF12 which is working like a charm

See u all

[Kerensa]

What kind of range are you getting with the Linksys WCF12?

Are you running it using encryption?

Thank you,
Kerensa

[friendharry]

Hi

My Buffalo WLI2 CF S11 doesn't work at all. The 3000 seems not to recognize it. Did you get any tips to configure the CF. Actually I just inserted the card without making any config.

Tks for your help

Serge

[FRH]

Kerensa :

I'm using a 128bits WEP key and  haven't done any kind of stats about range...sorry.

bye

[Munin]

NetGear MA701 worked fine right out of the box.

I've also tried a Zonet ZCF1100 and a SanDisk ConnectPlus (wi-fi + 128MB flash combo card), but so far no luck with either of those.

[Bertram Wooster]

SanDisk Connect Plus is not working. Though at a different forum some help seems to approach (especially thanks due to the man behind Cacko ROM):
http://www.dsitri.de/phpBB2/viewforum.php?f=21
Main point (as far as a newbie can decipher) is that you install HostAP drivers and change them slightly. For me, however, these hints are still a bit too much. Especially as I wouldn't dare flash my rom on the C3000.
Has anyone tried to successfully install HostAP on C3000?

[NTalent]

IP;DNS;Proxy.
Is there any way to show ESS-ID and ad-hoc network type as I use connection between 2 computers?