Bluetooth Under Debian Eabi

[Chero]

each time i plug my belkin cf bt card or when i resume from suspend, i've to type
hciattach /dev/ttyS4 bcsp
for it to work

do you know a way to do that automaticaly ?

http://lkrauss.de/zaurus/billionton-cfbt02-b2.php

Check the site above (it's in german), especially the /etc/bluetooth/uart file. My guess is you have to do something like that to make it work.

Chero.

[jpmatrix]

argh!
i've just tried again my belkin cf under debian eabi kernel 2.6.23 and it no longer works !!!
the card is discovered but when i hciattach it, it keeps on sending error messages that fill the screen without any chance to type something:

bcsp_recv: Error in BCSP hdr checksum
bcsp_recv: Short BCSP packet

i'll google to find out but anyone succeed in ? i'll try my msi bt dongle too

[jpmatrix]

my MSI usb BT dongle is working under debian eabi.
so i could have a bt dialup networking with my nokia gsm.
i update the top thread for now; i don't know what is happening about my Belkin CF BT...

[zeigerpuppy]

I am having a bit of trouble getting my (Socket Rev G I think) bluetooth card working
would like to use PPP via GPRS, had this working OK in pdaXrom

yonggon kernel 2.6.23.9
I have installed bluez-utils

pccardctl ident:
Socket 1
  product info: "Socket", "CF+ Personal Network Card Rev 2.5", "."
  manfid: 0x0104 0x0096
  function: 2 (serial)

hciattach: returns nothing

dmesg:
pccard: PCMCIA card inserted into slot 1
pcmcia: registering new device pcmcia1.0
pcmcia: request for exclusive IRQ could not be fulfilled.
pcmcia: the driver needs updating to supported shared IRQ lines.
ttyS0: detected caps 00000700 should be 00000100
1.0: ttyS4 at I/O 0xc48403f8 (irq = 169) is a 16C950/954

hciattach /dev/ttyS4 bcsp
BCSP initialization timed out

any ideas?

[Vitel]

any ideas?

Try this:

#setserial /dev/ttyS4 baud-base 921600
#hciattach -s 921600 /dev/ttyS4 bcsp

[jpmatrix]

any ideas?

Try this:

#setserial /dev/ttyS4 baud-base 921600
#hciattach -s 921600 /dev/ttyS4 bcsp

i'm just trying with my (working) Belkin CF BT and i have a "command not found" with the setserial command. I guess you've to install some package to have it working

which download speed do you have with your CF BT ? mine seems stuck to 9.28kb/s but i can reach more than 40 kb/s when using my USB BT dongle... i wonder if the setserial command would give better results.

[Vitel]

i'm just trying with my (working) Belkin CF BT and i have a "command not found" with the setserial command. I guess you've to install some package to have it working

apt-get install setserial

which download speed do you have with your CF BT ? mine seems stuck to 9.28kb/s but i can reach more than 40 kb/s when using my USB BT dongle... i wonder if the setserial command would give better results.

I have approximately the same limit for CF BlueTooth (Billionton).

[zeigerpuppy]

any ideas?

Try this:

#setserial /dev/ttyS4 baud-base 921600
#hciattach -s 921600 /dev/ttyS4 bcsp

No joy  

with
setserial /dev/ttyS4 baud_base 921600
hciattach -s 921600 /dev/ttyS4 bcsp

I still get BCSP initialization timed out

[laan]

any ideas?

Try this:

#setserial /dev/ttyS4 baud-base 921600
#hciattach -s 921600 /dev/ttyS4 bcsp

No joy  

with
setserial /dev/ttyS4 baud_base 921600
hciattach -s 921600 /dev/ttyS4 bcsp

I still get BCSP initialization timed out

After updating to last Angstrom kernel my Belkin CF BT is working perfectly, no need to change nothing, detected and attached at first, dial-up networking working fine with a V3x

[jpmatrix]

any ideas?

Try this:

#setserial /dev/ttyS4 baud-base 921600
#hciattach -s 921600 /dev/ttyS4 bcsp

No joy  

with
setserial /dev/ttyS4 baud_base 921600
hciattach -s 921600 /dev/ttyS4 bcsp

I still get BCSP initialization timed out

After updating to last Angstrom kernel my Belkin CF BT is working perfectly, no need to change nothing, detected and attached at first, dial-up networking working fine with a V3x

great! are you talkin about this kernel ?
zImage-2.6.23-spitz-20080106233423.bin

[laan]

I used:
http://www.angstrom-distribution.org/unsta...Image-spitz.bin

and

http://www.angstrom-distribution.org/unsta....6.23-spitz.tgz

[nickk9]

I cant get BT worked in eabi. I did all the steps from the first post and when i do 'pon provider' my phone (nokia 6310) asks about passkey, i enter the same passkey from hci.conf and then my nokia displays 'Connecting' progress bar forever. I use BT USB dongle. The very same hardware (phone, usb bt, zaurus) works fine in cacko, so i suppose its not hw problem.

hciconfig hci0 prints 'UP RUNNING PSCAN ISCAN' as it should. RX, TX error counters both zero.

The same BT binding problem i got immediate if i do 'rfcomm connect' instead of rfcomm 'bind', so i believe it is the problem with BT connection itself, not gprs/ppp issue.

Any suggestions ?

[nickk9]

Seems i solved the problem with http://www.zedd.nl/?p=8