Billiardz, Where To Find Newer Ipk?

[climber]

How is it possible to disable javascript  on the Zaurus? Could give me short instructions how to enable or disable it?

Thanks,
climber

[Jon_J]

How is it possible to disable javascript  on the Zaurus? Could give me short instructions how to enable or disable it?

Thanks,
climber
[div align=\"right\"][a href=\"index.php?act=findpost&pid=117730\"][{POST_SNAPBACK}][/a][/div]

I was using firefox on a winXP box. I don't have the internet connected to my Zaurus.

EDIT: I decided to remove billiardz from my C3100. I don't have enough knowledge to
enable it to work in 640x480. It's way too small as it runs now. I have a pool playing game
on my Palm Zire 72 that works very well, with sound effects, applause, ect.
Anyone who is looking for the 1.4 version of billiardz can download it from page 2 of this post.
It also has a depends. I'll post it below.

Depends (rename to libSDL-image_arm.ipk before installing.)

Jon

[Miami_Bob]

Just feedback on the packages on a C860 under Sharp ROM v1.40

D/L'd

  billiardz_0.1.4_arm.ipk ( 226.79k )

and

   libSDL_image_1.2.3_1_arm.ipk ( 16.68k )

from this thread.

Both installed to main memory without problems. When billiardz ran, the screen was in portrait mode but the table was rotated 90 degrees CCW (compared to v1.3) with portions off screen.

Unchecking the "magnified" box gave a display hashed at the top & locked the C860 hard. Needed to pull the battery & reboot to regain functions.

Is there a "help" or cheat sheet for the operation of the game (since it appears to be different from v1.3)?

This is the first time that I have gotten billiardz v1.4 to even run at all on the C860 so THANKS!!

[Miami_Bob]

Will have to correct my message above & add some details.

You need to rename

  libSDL_image_1.2.3_1_arm.ipk

to

  libSDL-image_1.2.3_1_arm.ipk

before installation will work.

After reboot, billiardz v1.4 on C860 failed to run. Console error message said it was due to a missing library file.

Realized that I had Meanie's XQt Jumbo cramfs mounted & live before the reboot. Reinitialized XQt Jumbo & billiardz v1.4 once again ran OK.

Appearance & functions same as in above message.

However, playing the 2 versions shows that v1.3 & v1.4 work essentially the same (I didn't know about the keyboard controls in v1.3 & only used stylus) except for the rotation of the table in v1.4 as above.

Fn + or - do not do anything on C860 display. Qtopia task bar shows under v1.4 rather than running "full screen" like v1.3 does.

Otherwise I haven't found any differences between v1.3 & v1.4 so far.

[telemetric_au]

i couldnt get 1.4 to run so here's 1.2

http://zaurus.spy.org/feeds/docs-zaurus-co...z_0.1.2_arm.ipk

[booyaa]

I found billiardz_0.1.3_arm.ipk at the Sharp website, but it caused the screen to lockup.
I had to remove the battery on one occasion. I checked & unchecked Display with magnified screen.
running as root, it fails to write to a directory that has been fixed in the 0.1.4 version.
I noticed billiardz_0.1.4_arm.ipk on ELSI and killfiz, but the page that it's located on is gone.
Does anyone have this?
I've been trying it on a C3100
Googling for billiardz_0.1.4_arm.ipk, just takes me to old forums or dead links.
Thank you,
Jon
[div align=\"right\"][{POST_SNAPBACK}][/a][/div]

et viola zaurus.spy.org comes to the rescue: [a href=\"http://zaurus.spy.org/feeds/docs-zaurus-com/billiardz_0.1.2_arm.ipk]http://zaurus.spy.org/feeds/docs-zaurus-co...z_0.1.2_arm.ipk[/url]

yes it's 0.1.2, but it's better than nothing.  

[Cresho]

it needs this version.  the same version that i will be including with the gngeo which makes it work

http://www.gnurou.org/software/zaurus/feed....5cvs-1_arm.ipk

and any billiards version will do.  i have 1.4

make sure you have libsdl's installed.  if your running my combo emulators, just install this libsdl image version and you will be fine.

keep magnify ticked or you will be sorry!