Re@lity doesn't have a personal statement currently.
Gender Not Set
Joined: 15-November 04
Profile Views: 284*
Last Seen: 20th February 2005 - 12:30 PM
Local Time: Sep 19 2014, 03:49 AM
10 posts (0 per day)
* Profile views updated each hour
18 Feb 2005
Please can anyone tell me of *any* CF WiFi cards that will load up HostAP drivers *automatically* in pdaXrom ??
I bought a Senao (Prism) CF card - NL2511 CF Mercury - but pdaXrom loads it up using Spectrum drivers, I *think* it was. Anyway, I cannot get it to run on HostAP drivers. I've tried editing the usual config files with the cards manfid etc etc & binding it to hostap, without any luck.
So, what *will* load up with hostap straight away in pdaXrom??
Maybe a Linksys WCF12 ??
Or an Ambicom WL110C ??
Could anyone that uses one of these cards please let me know if it's always used Hostap by "default" or even if they had to force it to use Hostap, how you did it?
Thanks in advance for *any* help/ideas.
13 Feb 2005
Please can anyone tell me of any CF wifi cards that will be correctly recognised at boot time & load up automatically using the Hostap drivers ??
Does pdaXrom use Hostap automatically for any cards, or is it a re-config job only?? Any comments pdaXrom Dev Team, please?
I know I need a Prism based card, but which ones does pdaXrom (rc8 or rc9)support "out of the box"??
I was looking into the Linksys WCF12 card & the Dlink 660w.
Does anyone have one of these, or any others & know if it all works automatically with Hostap drivers, or is there any config changes that need to be made??
Thanks very much for any help/ideas
9 Feb 2005
Please can anyone tell me how to get my Senao NL2511 CF Mercury card to work with hostap drivers?
Does Rc8 or Rc9 have *working* Hostap built in?
Or should I install the ones I found here on the forum? I can "modprobe hostap_cs" & then they're listed in lsmod, but how do you get them to load at startup?
I've tried adding the cardctl ident output to various .conf files.
I can't seem to sort this out! All I keep getting at boot up is "Unsupported card" msg, followed with the card info I put in.
Failing all that, is there a Prism based card *known* to work easily with hostap drivers?
I'll happily buy a new card if it solves this hostap problem!
I just want a Prism based card & hostap working! It's why I bought a c700 last week, just for pdaxrom, hostap etc.
I have a 5500 with working hostap etc, on OZ, but I would love to have it on the pdaXrom OS on the c700 instead.
*Please* does anyone have any ideas? I've been struggling with this for a good few days now ;(
8 Feb 2005
How can I get HostAP running in rc8 or rc9??
Just want to use a Senao Prism based card with the HostAP drivers.
Any help would be greatly appreciated!
15 Nov 2004
Should OZ + GPE flash from an SD card or does it have to be a Compact Flash card?
I've tried with SD (all i have atm!) but no go......in fact I thought I'd made a nice shiny new brick
It was completely dead - not even an orange power light when plugged into AC
But then I found a quick hard reset resuccitated it!!
Anyway, when trying the C + D + Reset sequence I got no lights - not even the green + orange 1sec flash on & off when no images are found.
So, is it me or the SD card? Will I have to wait untill I get the Compact Flash card sorted?
Thanks for any advice, comments, thoughts....
Other users have left no comments for Re@lity.
There are no friends to display.
|Lo-Fi Version||Time is now: 18th September 2014 - 07:49 PM|