OESF Portal | OESF Forum | OESF Wiki | LinuxPDA | #planetgemini chat on matrix.org | #gemini-pda chat on Freenode | #zaurus and #alarmz chat on Freenode | ELSI (coming soon) | Ibiblio

IPB

Welcome Guest ( Log In | Register )

2 Pages V   1 2 >

7_feet_up
Posted on: Jun 20 2009, 03:38 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


My Sharp Zaurus SL-5600 (a.k.a. "Poodle") is for sale. It's in good condition and fully functional.

It comes with several accessories:
1. Peak CF 512 Mb
2. Sandisk SD 64 Mb
3. Senao CF 802.11b Wifi card
4. Destinator CF GPS receiver + external antenna
5. CE-ST9 USB cradle
6. CE-170TS serial cable
7. Piel Frama luxurious leather PDA-case with the colors Black/Tan
8. Trust PW-2992p 2800 mAh external battery

I'm asking €100 or the best offer.





  Forum: For Sale / Wanted · Post Preview: #182565 · Replies: 0 · Views: 1,955

7_feet_up
Posted on: May 24 2008, 11:16 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


QUOTE(msjones @ May 4 2008, 06:02 PM) *
Is the 3.5.4 oz pretty stable? It seems ok so far.

Openzaurus is obsoleted by Angstrom, so you should switch to Angstrom. Poodle is supported and actively maintained. Angstrom uses the 2.6 kernel and is easy to use with altboot. There even are ready-built poodle images for use with altboot available.
  Forum: 5x00 General discussions · Post Preview: #177495 · Replies: 3 · Views: 4,391

7_feet_up
Posted on: Mar 8 2007, 05:00 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


Zie mijn reactie op je vraag in een ander topic.
  Forum: Netherlands · Post Preview: #155756 · Replies: 1 · Views: 3,535

7_feet_up
Posted on: Mar 8 2007, 04:54 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


QUOTE(rlvb @ Feb 23 2007, 02:48 PM)
QUOTE(gamemastermischa @ May 10 2005, 01:11 PM)
Hallo,

Hier nog een Zaurus gebruiker, al een tijdje, maar ach.
Ik ben een blije bezitter van een 5500. (Rom 3.10)

Zijn er hier nog meer mensen met een 5500?
Zo ja, iemand ervaring met:

Bluetooth
Installeren van een andere ROM

Gamemaster.
*


hoi,hoop dat iemand mij kan helpen. Heb veel gelezen over de sharp sl-5500g. Heb hem zeer goedkoop op de kop kunnen tikken en wil hem graag gebruiken. Heb hem opgeladen en de benodigde software erbij gezocht. Maar als ikhem wil aanzetten krijg ik een zwart scherm met de woorden sharp, wat doe ik verkeerd en als ie stuk is, waar in nederland kan ik hem laten repareren, want sharp NL doet dat niet.Wie helpt mij en wie kanmij vertellen wat er mis is met dit mooie apparaat. ik werk onder xp prof
*



Het zwarte scherm met in rode letters "SHARP" is het splashscherm dat je altijd ziet bij het opstarten. Als je zaurus niet verder komt dan dit, staat er mogelijk geen besturingssysteem op. Het betekent niet automatisch dat hij stuk is (al weet ik dat natuurlijk niet zeker). Als je de zaurus eerst reset (met het knopje achter het batterijklepje) en daarna de Cancel en OK knop tegelijk indrukt, krijg je een menu te zien. Je zou eerst kunnen proberen om via dit menu de zaurus te formatteren. Als dit geen verschil maakt, zou je een nieuwe ROM moeten installeren. De beste keus is OpenZaurus, omdat deze nog actief wordt ontwikkeld (http://wiki.openzaurus.org/Collie/Install). De originele Sharp ROM is hier te downloaden: http://www.myzaurus.com/downloads3.asp. Omdat je zaurus momenteel niet opstart, zul je de ROM wel op een andere manier op een CF of SD kaartje zien te krijgen.
  Forum: Netherlands · Post Preview: #155754 · Replies: 10 · Views: 11,786

7_feet_up
Posted on: Oct 21 2006, 10:30 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


QUOTE(simbaB @ Oct 13 2006, 09:36 PM)
I am getting an error about html4.css when I try to run the new Konqueror. I installed to /home and did the 'ipkg-link mount /home' bit, too.

You have to add the environment variable KDEDIR so konqueror can find it. I added the instruction to my post above.
Also, you have to install one of the qte-fonts.
  Forum: Angstrom & OpenZaurus · Post Preview: #144460 · Replies: 16 · Views: 8,350

7_feet_up
Posted on: Oct 12 2006, 10:56 PM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


@Greg2

That's odd, I installed it @home without changes. Just linking the lot with ipkg-link did the job. I left the bb file untouched as well. The only thing I did is building what was already in the dev branch of OE.

Folkert

BTW nice avatar wink.gif I should look for another one, I'm afraid.
  Forum: Angstrom & OpenZaurus · Post Preview: #143899 · Replies: 16 · Views: 8,350

7_feet_up
Posted on: Oct 12 2006, 03:26 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


I couldn't get opera to work in openzaurus 3.5.4.2-rc2. In previous versions I could, with minor and major hassles. Because opie's konqueror-embedded is about three years old and cannot be made to work with wifi hotspots like those in the Netherlands. Thus, I gave up on opera and built the development version of konqueror-embedded. Get the ipk here.
  Forum: Angstrom & OpenZaurus · Post Preview: #143828 · Replies: 50 · Views: 41,388

7_feet_up
Posted on: Oct 12 2006, 12:20 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


I experienced the same problem of not being able to acces a wifi hotspot in the Netherlands with opie and the three-years-old konqueror-embedded (version 20030705) on my poodle. I never considered it a problem since opera worked for me with the compat libs, until recently. When I flashed to openzaurus 3.5.4.2-rc2, opera stopped working, and with it the wifi surfing.
The solution for me was to upgrade konqueror-embedded to the development version (version 20060404). However, I had to build it using openembedded. Unfortunately I don't have a server with enough bandwith at my disposal to maintain a feed on my own. I have attached the needed ipk's to this message.



1. Install the attached ipk's. Note that these ipk's are built for poodle. Because ipkg crashed by shortage of RAM installing these packages, I had to close all applications (including opie) to save RAM. So it might be necessary to ssh into your zaurus or install in the terminal on your Z.
2. Install one of the qte-fonts, e.g. qte-font-helvetica-small
3. Add the environment variable KDEDIR by adding a line to /etc/profile.d/opie_defaults:
CODE
echo "export KDEDIR=/usr" >> /etc/profile.d/opie_defaults

4. Then, copy the attached konqueror.png icon to /opt/QtPalmtop/pics/
5. To create an icon in opie's Applications tab, you have to add this .desktop file by hand:

/opt/QtPalmtop/apps/Applications/konqueror.desktop:
CODE
[Desktop Entry]
Comment=Konqueror
Exec=konqueror
Icon=konqueror.png
MimeType=text/html;
Type=Application
Name=Konqueror
CanFastload=1
Display=640x480/144dpi,480x640/144dpi
HidePrivilege=1
NeedSpace=8192
  Forum: Angstrom & OpenZaurus · Post Preview: #143812 · Replies: 16 · Views: 8,350

7_feet_up
Posted on: May 3 2006, 02:32 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


QUOTE(NickNak @ May 1 2006, 09:17 PM)
I have run into problems with my bridging setup:  I can log into my SL-5500 using ssh, ping hosts on the internet, download small files using wget, but if I try to download anything bigger than about 1k I get "no response from the server".  I have noticed that usb0 on the desktop gets an MTU of 1494 whereas usbd0 at the other end on the Zaurus gets an MTU of 1500. I can't increase usb0 to 1500 on the desktop, but if I decrease usbd0 to 1494 on the Z ('ifconfig usbd0 mtu 1494') the problem is fixed.  My question is: why doesn't this 'just work'?  Why do usb0 and usbd0 get different MTUs? Is there a bug somewhere, or is there something wrong with my setup?
*

I don't know what causes the necessity to shrink the mtu, but the issue has been described before on the usbnet driver page and already has been reported on the kernel bugzilla. I certainly would consider it a bug, either on the zaurus side, or on the desktop side.
  Forum: Angstrom & OpenZaurus · Post Preview: #125544 · Replies: 46 · Views: 111,296

7_feet_up
Posted on: Mar 20 2006, 01:24 PM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


QUOTE(Storm @ Jan 30 2006, 11:24 PM)
<snip>
I have questions, since it does not seem to work for me.
<snip>

Sorry about the late reply. I don't regularly check this thread, so you could as well have solved the issue by now. Anyway, I updated the howto. Just delete the udev rule and add the lines to /etc/network/interfaces as described in the howto.
QUOTE(Storm @ Jan 30 2006, 11:24 PM)
Once I get this up and working, I would like to append something like the following to bring up out-to-the-internet connectivity for the zaurus:
<snip>
But one step at a time...

--Storm

To run commands after the interface has been brought up, use the 'up' command in /etc/network/interfaces, and the 'post-down' command after taking the interface down:
CODE
allow-hotplug usb0
mapping hotplug
      script grep
      map usb0

iface usb0 inet static
address 192.168.129.200
netmask 255.255.255.0
pointopoint 192.168.129.201

pre-up modprobe iptable_filter
pre-up modprobe iptable_nat
pre-up modprobe ip_nat_ftp
pre-up modprobe ip_conntrack_ftp
pre-up modprobe ip_conntrack_irc
pre-up modprobe ip_nat_irc
up echo "1" > /proc/sys/net/ipv4/ip_forward
up iptables -t filter -F FORWARD
up iptables -t filter -P FORWARD DROP
up iptables -t filter -A FORWARD -s 192.168.129.0/24 -j ACCEPT
up iptables -t filter -A FORWARD -d 192.168.129.0/24 -j ACCEPT
up iptables -t nat -F PREROUTING
up iptables -t nat -P PREROUTING ACCEPT
up iptables -t nat -F POSTROUTING
up iptables -t nat -P POSTROUTING ACCEPT
up iptables -t nat -F OUTPUT
up iptables -t nat -P OUTPUT ACCEPT
up iptables -t nat -A POSTROUTING -s 192.168.129.0/24 -o usb0 -j MASQUERADE
post-down echo "0" > /proc/sys/net/ipv4/ip_forward
post-down iptables -t nat -F

Folkert.
  Forum: Angstrom & OpenZaurus · Post Preview: #119454 · Replies: 46 · Views: 111,296

7_feet_up
Posted on: Jan 24 2006, 03:00 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


QUOTE(microsoft/linux @ Jan 23 2006, 06:49 AM)
what happens if the usbnet driver is built into my kernel. I custom build my kernel, the scripts should still work right?
*

It shouldn't make a difference.
  Forum: Angstrom & OpenZaurus · Post Preview: #112149 · Replies: 46 · Views: 111,296

7_feet_up
Posted on: Dec 23 2005, 04:27 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


Dropbear is a ssh server that provides remote shell access to your zaurus. It enables you to log into your zaurus and to execute commands in a shell. The default shell in OpenZaurus is the Bourne shell, or sh. So what you are looking for is a howto of the shell, not ssh or dropbear.
Although sh is used as an interactive command interpreter, it was always intended as a scripting language. A few links to tutorials of the shell:
UNIX Shell Script Tutorials & Reference
UNIX/Linux Bourne/Bash Shell Scripting Tutorial
  Forum: Angstrom & OpenZaurus · Post Preview: #108205 · Replies: 4 · Views: 1,476

7_feet_up
Posted on: Dec 17 2005, 09:08 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


Debian unstable Zaurus USB-network how-to:
Install the latest stock kernel for your machine class e.g.:
CODE
user@desktop:~# sudo apt-get install linux-image-2.6.14-2-686

Reboot.
Plug in the zaurus and see if it was recognized by your computer. By issueing the command 'tail /var/log/messages' you will see the last few lines of your system log. You should see that an usb device was connected, the 'zaurus' module was loaded and that your zaurus was recognized:
CODE
user@desktop:~# tail /var/log/messages
Dec 17 17:35:58 localhost kernel: usb 2-2: new full speed USB device using uhci_hcd and address 10
Dec 17 17:35:58 localhost kernel: usb0: register 'zaurus' at usb-0000:00:10.0-2, pseudo-MDLM (BLAN) device, 52:8c:8b:4f:e4:90

Find that the module was loaded:
CODE
user@desktop:~# lsmod | grep zaurus
usbnet                 17064  2 zaurus,cdc_ether

You'll probably have one or two more lines containing the word 'zaurus', but you definitely should have this line here. If not, something went wrong with loading the module.
An 'ifconfig -a' should give you a usb0 network interface, which isn't configured yet. There may be more network interfaces depending on your system, but usb0 should definitely be there.
CODE
user@desktop:~# ifconfig -a
usb0      Link encap:Ethernet  HWaddr 52:8C:8B:4F:E4:90
         BROADCAST MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

Now we'll configure the network interface of the zaurus and your linux computer. We'll give your computer and your zaurus a static IP.
First your zaurus:

Start 'Network' in your Settings dir. Click on the interface 'usbd0' and click configure.

Fill in the Following:

(X) Automatically bring up
( ) DHCP

Static Ip Configuration
IP Address 192.168.129.201
Subnet Mask 255.255.255.0

Leave the rest empty for now.

On your linux computer type the following:
CODE
sudo ifconfig usb0 192.168.129.200 netmask 255.255.255.0 up

This should configure your USB network interface and bring it up. Now we'll try if we can reach the zaurus. We'll do this by pinging it's IP address (the command should be stopped by typing Ctrl-c or it will go on forever):
CODE
user@desktop:~# ping 192.168.129.201
PING 192.168.129.201 (192.168.129.201) 56(84) bytes of data.
64 bytes from 192.168.129.201: icmp_seq=1 ttl=64 time=0.108 ms
64 bytes from 192.168.129.201: icmp_seq=2 ttl=64 time=0.094 ms
64 bytes from 192.168.129.201: icmp_seq=3 ttl=64 time=0.090 ms
64 bytes from 192.168.129.201: icmp_seq=4 ttl=64 time=0.089 ms
64 bytes from 192.168.129.201: icmp_seq=5 ttl=64 time=0.093 ms

--- 192.168.129.201 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 3998ms
rtt min/avg/max/mdev = 0.089/0.094/0.108/0.014 ms

Now we will make your configuration permanent. You don't want to type 'ifconfig usb0 192.168.129.200 netmask 255.255.255.0 up' to use your zaurus all the time, and you'll probably just want to stick it in to be able to use it. There are (at least) two ways to accomplish this task:
1. by adding an entry for the usb interface in the file /etc/network/interfaces, or
2. by writing a new udev rule that configures the usb interface

1. The first option is the easiest and, in my opinion, the cleanest. As root, add the following lines to the file /etc/network/interfaces:
CODE
allow-hotplug usb0
mapping hotplug
       script grep
       map usb0

iface usb0 inet static
address 192.168.129.200
netmask 255.255.255.0
pointopoint 192.168.129.201


2. The second option also works, but should be considered a hack. So you'd better skip this one. I will leave it in this post for historical purposes though, since untill I found out about the option printed above this was the only way I could bring up the usb interface automatically. It requires writing a new udev rule that configures the usb interface based on 2 keys: the kernel device name (e.g. usb0) and the driver used, that is 'zaurus'. You actually could omit this key, but then this rule would interfere with other devices with a usb* device name (probably usb networking devices), if you owned such a device. (It appeared that the hardware address used in a previous version of this post changes every other time you reboot your machine. Since the address isn't permanent, it isn't suitable as a key.)

So, as root, create the file /etc/udev/zaurus.rules and add the following line:
CODE
KERNEL=="usb[0-9]*", DRIVER="zaurus", NAME="%k", SYMLINK="zaurus", RUN+="/sbin/ifconfig %k 192.168.129.200 netmask 255.255.255.0 up"


and symlink it to the directory /etc/udev/rules.d:
CODE
$ cd /etc/udev/rules.d
user@desktop:~# sudo ln -s ../zaurus.rules 10_zaurus.rules


Now restart the udev daemon:
CODE
user@desktop:~# sudo /etc/init.d/udev restart

This will ensure that every time your zaurus hits the cradle the network connection will be started.

If your connection to the zaurus often hangs for no apparent reason, consider shrinking the MTU on the zaurus:
CODE
root@zaurus:~# ifconfig usb0 mtu 1000

To make the change permanent, even after rebooting, add the line "mtu 1000" to the section of the usbd0 network interface in the /etc/network/interfaces file.

Folkert van der Beek.


*edit: modified the udev rule, so it won't interfere with other usb networking devices.
*edit2: modified the udev rule to identify the zaurus based on the driver in stead of the hardware address, since the latter apparently changes after every reboot.
*edit3: added the option to modify /etc/network/interfaces, instead of writing an udev rule.
*edit4: added the option to shrink the MTU to prevent freezing connections.
  Forum: Angstrom & OpenZaurus · Post Preview: #107401 · Replies: 46 · Views: 111,296

7_feet_up
Posted on: Dec 8 2005, 01:43 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


I bought one and it fits! Despite the bigger battery compartment of the SL-5600, the leather is flexible enough to contain it and look pretty as well.
  Forum: For Sale / Wanted · Post Preview: #106438 · Replies: 5 · Views: 1,986

7_feet_up
Posted on: Dec 2 2005, 10:23 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


Ipkg fails to install local packages. Instead, ipkg locates the package in the online feeds and installs it. Only the -offline option causes the package to be being installed.
  Forum: Angstrom & OpenZaurus · Post Preview: #105803 · Replies: 80 · Views: 31,735

7_feet_up
Posted on: Dec 2 2005, 09:25 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


I use zbedic a lot on my zaurus. But the latest package in the feeds is zbedic_20041227-r1. Since then, there have been a few updates. The latest release is version 0.9.6 from 2005-06-23 which has quite a few enhancements.
I hope someone with acces to the feeds reads this post and will update the package.

Regards,
Folkert.
  Forum: User Request for Applications · Post Preview: #105800 · Replies: 1 · Views: 2,116

7_feet_up
Posted on: Dec 1 2005, 09:27 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


QUOTE(rmrfchik @ Dec 1 2005, 01:15 PM)
QUOTE(7_feet_up @ Dec 1 2005, 12:45 AM)
The problem lies in the usbnet module. Since kernel 2.6.14 the module is split up in several sub-modules. The module needed to talk to your zaurus is now 'cdc_subset' in stead of 'usbnet'. It works perfectly fine after adjusting this.
*

I rmmod zaurus, cdc_ether and usbnet and then modprobe cdc_subset. The problem remain.
*


Your signature says you use Debian. If you use stock kernels in stead of custom ones, try linux-image-2.6.14-2, since 2.6.14-1 didn't work out of the box.
  Forum: Linux Issues · Post Preview: #105699 · Replies: 18 · Views: 21,466

7_feet_up
Posted on: Nov 30 2005, 01:45 PM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


The problem lies in the usbnet module. Since kernel 2.6.14 the module is split up in several sub-modules. The module needed to talk to your zaurus is now 'cdc_subset' in stead of 'usbnet'. It works perfectly fine after adjusting this.
  Forum: Linux Issues · Post Preview: #105609 · Replies: 18 · Views: 21,466

7_feet_up
Posted on: Nov 11 2005, 09:57 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


I use a Senao NL-2511CF Mercury CF WLAN card with my zaurus SL-5600 running openzaurus 3.5.3, and it works just fine. For a list of supported wireless cards, see the Zaurus FAQ.
  Forum: 5x00 General discussions · Post Preview: #103340 · Replies: 8 · Views: 2,469

7_feet_up
Posted on: Oct 20 2005, 12:20 PM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


For about a year I own a zaurus sl-5600. Until now, I have been carrying around my zaurus without a case in my pocket. Only the screen is protected with a plastic cover. The buttons stay uncovered, so the device is switched on and off and starting applications by accident all day, draining the battery. I recently found that Piel Frama made a leather case for the 5500. That case would prove very useful for my zaurus sl-5600. But I wonder if the case fits the 5600, despite the bigger battery.

Someone tried it yet?
  Forum: For Sale / Wanted · Post Preview: #100242 · Replies: 5 · Views: 1,986

7_feet_up
Posted on: Jul 3 2005, 03:28 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


From kernel version 2.6.12 and on, the usbnet issue is solved. No patch needed.
  Forum: Linux Issues · Post Preview: #86818 · Replies: 2 · Views: 3,951

7_feet_up
Posted on: Jun 29 2005, 11:50 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


I use opie-reader a lot with pages I retrieve from the internet using Plucker for linux from www.plkr.org. This all works fine, and I'm very content with it. The only thing is that all links get striked through after clicking on them in opie-reader (or maybe they get underlined, but seem strikedthrough). These links aren't dead ones, btw. The links continue to work, so it's annoying at worst. Does anyone else experience the same odd behavior and, better, does anyone know how to prevent it?
  Forum: Angstrom & OpenZaurus · Post Preview: #86346 · Replies: 0 · Views: 1,016

7_feet_up
Posted on: Jun 15 2005, 10:21 PM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


You're not the first one to notice. Please read this topic.
  Forum: Linux Issues · Post Preview: #84473 · Replies: 9 · Views: 6,018

7_feet_up
Posted on: Jun 5 2005, 01:31 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


As many already noticed, usbnet for zaurus was broken since kernel 2.6.11.
Good news: it now works again in 2.6.12-rc5.
I also applied the usbnet_zaurus.patch from David Brownell he submitted 3 june in the fa.linux.kernel newsgroup, which I don't know was necessary since I own the zaurus sl-5600, not sl-6000.
Here's the patch:
CODE
This "obvious" one-liner is needed to recognize Zaurus SL 6000;
it just checks two GUIDs not just one.

From: Gerald Skerbitz <gsker@tcfreenet.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

--- linux-2.6.12-rc5/drivers/usb/net/usbnet.c.orig    2005-06-01 18:06:20.000000000 -0500
+++ linux-2.6.12-rc5/drivers/usb/net/usbnet.c    2005-06-01 18:29:30.000000000 -0500
@@ -2765,7 +2765,7 @@ static int blan_mdlm_bind (struct usbnet
   }
   /* expect bcdVersion 1.0, ignore */
   if (memcmp(&desc->bGUID, blan_guid, 16)
-        && memcmp(&desc->bGUID, blan_guid, 16) ) {
+        && memcmp(&desc->bGUID, safe_guid, 16) ) {
       /* hey, this one might _really_ be MDLM! */
       dev_dbg (&intf->dev, "MDLM guid\n");
       goto bad_desc;
  Forum: Linux Issues · Post Preview: #82825 · Replies: 2 · Views: 3,951

7_feet_up
Posted on: May 30 2005, 11:27 AM





Group: Members
Posts: 27
Joined: 19-April 05
From: Netherlands
Member No.: 6,917


Hallo,
Een late reactie, maar er gebeurt nooit wat in de nederlandse sectie van dit forum. Maar wel leuk om eens iemand uit Nederland te spreken met een zaurus, die zullen er weinig zijn. Ik heb sinds een aantal maanden een (tweedehands aangeschafte) 5600. Hierop was de Zynergy ROM geïnstalleerd, omdat dat handig zou zijn voor WIFI. Ik heb het WIFI kaartje niet overgenomen, maar blaas alles door de usb-kabel tussen computer en zaurus heen en weer. Ervaring met bluetooth heb ik ook niet.

Ervaring met het installeren van andere ROMs heb ik wel. Na aankoop heb ik de zaurus vrijwel meteen voorzien van OpenZaurus 3.5.2. Ik heb ook nog even de Sharp ROM geprobeerd, maar binnen enkele dagen was ik weer terug bij OpenZaurus. Dit beviel toch het best. Het is volgens mij zeker aan te bevelen over te stappen naar OpenZaurus. Dat is namelijk nog volop in ontwikkeling in tegenstelling tot de Sharp ROM. Het nadeel is dat je Opera, Jeode en Hancom Word en Sheet met een kunstgreep zult moeten installeren (valt reuze mee hoor).

Ik moet nog kijken wat de voordelen zijn om op te waarderen naar 3.5.3. Ook overweeg ik eens gpe te installeren in plaats van (of naast) opie, omdat je daarmee de mogelijkheid hebt om een nette tekstverwerker (Abiword) te installeren. Hancom word is nagenoeg waardeloos, en Textmaker vind ik weer vrij duur voor die enkele maal dat ik een word documentje wil openen op m'n zaurus.

Folkert.
  Forum: Netherlands · Post Preview: #82176 · Replies: 10 · Views: 11,786

2 Pages V   1 2 >

New Posts  New Replies
No New Posts  No New Replies
Hot topic  Hot Topic (New)
No new  Hot Topic (No New)
Poll  Poll (New)
No new votes  Poll (No New)
Closed  Locked Topic
Moved  Moved Topic
 

RSS Lo-Fi Version Time is now: 26th May 2020 - 01:05 AM