OESF | ELSI | pdaXrom | OpenZaurus | Zaurus Themes | Community Links | Ibiblio

IPB

Welcome Guest ( Log In | Register )

Profile
Personal Photo
Options
Options
Personal Statement
Mainframe-junkie doesn't have a personal statement currently.
Personal Info
Mainframe-junkie
Age Unknown
Gender Not Set
Ebbelwoi-Town
Birthday Unknown
Interests
No Information
Statistics
Joined: 9-March 08
Profile Views: 574*
Last Seen: 26th May 2008 - 05:09 AM
Local Time: May 26 2013, 03:53 AM
15 posts (0 per day)
Contact Information
AIM No Information
Yahoo No Information
ICQ No Information
MSN No Information
Contact Send Message
Contact Private
* Profile views updated each hour

Mainframe-junkie

Members


Topics
Posts
Comments
Friends
My Content
6 Apr 2008
Hello friends,

i have installed the new stable image Angstrom-X11-2007.12-R14 from 1.April.
The first test showed an wrong script under /etc/network/if-pre-up.d/wpasupplicant (from Ubuntu, it fails with sed of busybox not knowing --quite) get called.
So i just linked wpa-supplicant to wpasupplicant.
When i try to connect to my WPA-WLAN with an NetGear MA-401RA (Firmware PRI v1.1.1, STA v1.8.2), it will get no connection.
The cards is ok, under simpad i can connect to an open WLAN.
My interfaces looks like
CODE
root@simpad:~$ cat /etc/network/interfaces
# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)

# The loopback interface
auto lo
iface lo inet loopback


# Wireless interfaces
#
#
iface wlan0 inet static
     address 192.168.2.7
     netmask 255.255.255.0
     network 192.168.2.0
     broadcast 192.168.2.255
     wpa-conf /etc/wpa_supplicant.conf
     wpa-driver hostap
#
#


and the content of wpa_supplicant.conf is

CODE
root@simpad:~$ cat /etc/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
network={
    ssid="BlueZone"
    key_mgmt=WPA-PSK
    pairwise=TKIP
    group=TKIP
    psk="01234567890123"
    priority=1
}
network={
    ssid="carioca"
    key_mgmt=NONE
    priority=2
}


I can see my WLAN with iwlist scan :

CODE
wlan0     Scan completed :
          Cell 01 - Address: 00:04:0E:D4:F4:B1
                    ESSID:"BlueZone"
                    Mode:Master
                    Frequency:2.422 GHz (Channel 3)
                    Signal level=-68 dBm  Noise level=-89 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
                    Extra:bcn_int=100
                    Extra:resp_rate=10
                    IE: WPA Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : TKIP
                        Authentication Suites (1) : PSK


In /var/log/messages i only found :

CODE
....
Apr  6 13:54:14 simpad user.debug kernel: prism2: wlan0: operating mode changed 3 -> 2
Apr  6 13:54:14 simpad user.info kernel: NET: Registered protocol family 17
Apr  6 13:54:14 simpad user.debug kernel: wifi0: LinkStatus=2 (Disconnected)
Apr  6 13:54:14 simpad user.debug kernel: wifi0: LinkStatus: BSSID=44:44:44:44:44:44
Apr  6 13:54:15 simpad user.notice root: Checking for WLAN association...
Apr  6 13:54:15 simpad user.notice root: Found association!
Apr  6 13:54:15 simpad user.debug kernel: wifi0: LinkStatus=2 (Disconnected)
Apr  6 13:54:15 simpad user.debug kernel: wifi0: LinkStatus: BSSID=44:44:44:44:44:44
Apr  6 13:54:15 simpad user.debug kernel: wlan0: Trying to join BSSID 00:04:0e:d4:f4:b1
Apr  6 13:54:15 simpad daemon.info avahi-daemon[2702]: Joining mDNS multicast group on interface wlan0.IPv4 with address 192.168.2.7.
Apr  6 13:54:15 simpad daemon.info avahi-daemon[2702]: New relevant interface wlan0.IPv4 for mDNS.
Apr  6 13:54:15 simpad daemon.info avahi-daemon[2702]: Registering new address record for 192.168.2.7 on wlan0.IPv4.
Apr  6 13:54:15 simpad user.debug kernel: wifi0: LinkStatus=6 (Association failed)
....


My router is an Fritz!Box and another embedded linux device, my iLiad (e-book from iRex) is working fine with WPA-WLAN.
I'm shure my psk is ok, because it contains only digits [0-9] like above ... wink.gif

Attached is an log of the session with output of various commands (iwconfig, ifconfig, iwscan, lsmod etc.) and more content of /var/log/messages

Did anyone run succsessfully WPA with Angstrom 2007.12 on simpad ?
Or any guesses what else to try/check/do ...???

Best regards and thanks to all which work on Angstrom for Simpad

Oliver

Attached File  Simpad_04.06.135001.txt ( 31.8K ) Number of downloads: 1

Edit : changed Topic description
9 Mar 2008
Hello friends,

after reading the thread abut the new image with PCMCIA support i decides to flash the image http://www.angstrom-distribution.org/unsta...ad.rootfs.jffs2,
after rebooting Simpad hangs with the following messages :
CODE
.udev/ already exists on the static /dev!                                        
Starting the hotplug events dispatcher udevd                                            
Synthesizing the initial hotplug events                                      
hostap_cs: Registered netdevice wifi0                                    
hostap_hw.c: INTERRUPT BEFORE DEVICE INIT!                                          
hostap_cs: index 0x01: , irq 1, io 0xc4800000-0xc480003f                                                        
wifi0: NIC: id=0x800c v1.0.0                            
wifi0: PRI: id=0x15 v1.1.1                          
wifi0: STA: id=0x1f v1.7.4                          
wifi0: NIC: id=0x800c v1.0.0                          
wifi0: PRI: id=0x15 v1.1.1                          
wifi0: STA: id=0x1f v1.7.4                          
Waiting for /dev to be fully populated                                      
Remounting root file system...                              
root: mount: special device /dev/mtdblock/2 does not exist                                                          
Setting up IP spoofing protection: rp_filter.                                            
Configuring network interfaces... SIOCGIFFLAGS: No such device                                                              
eth0      No such device                        

udhcpc (v1.2.1) started                      
udhcpc[2641]: udhcpc (v1.2.1) started                                    
SIOCGIFINDEX failed!: No such device                                    
udhcpc[2641]: SIOCGIFINDEX failed!: No such device                                                  
done.    
Starting portmap daemon: portmap.                                
BUG: soft lockup - CPU#0 stuck for 11s! [hwclock:2664]                                                      

Pid: 2664, comm:              hwclock                                    
CPU: 0    Not tainted  (2.6.24 #1)                                  
PC is at __do_softirq+0x4c/0xd0                              
LR is at __do_softirq+0x2c/0xd0                              
pc : [<c003d240>]    lr : [<c003d220>]    psr: 60000013                                                      
sp : c2c03d84  ip : c2c03d84  fp : c2c03d9c                                          
r10: c032d424  r9 : c2c02000  r8 : 00000002                                          
r7 : 00000003  r6 : 0000000a  r5 : c0358e5c  r4 : 00000022                                                          
r3 : 20000013  r2 : c0358e20  r1 : 00000104  r0 : 00000000                                                          
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment us                                                            
Control: c2c1b17f  Table: c2c1b17f  DAC: 00000015

I attach the logs for further information.Attached File  Simpad_boot.txt ( 22.72K ) Number of downloads: 6


Thanks for any suggestions and help

Oliver
Last Visitors


28 Mar 2008 - 11:40


20 Mar 2008 - 7:05


9 Mar 2008 - 14:03

Comments
Other users have left no comments for Mainframe-junkie.

Friends
There are no friends to display.
RSS Lo-Fi Version Time is now: 25th May 2013 - 05:53 PM
Powered By IP.Board © 2013  IPS, Inc.
Licensed to: Roy El-Rayes, oesf.org